,
Europees netwerk van dealers van voorraadhoudende machines

Bitte einen Suchbegriff eingeben - Voer een zoekterm in
Categorie:
    Fabrikant:
      machines:
        Handelaar:

          Machines available immediately

          Machinelist: Machines available immediately


          Center Lathe

          used Machines available immediately Center Lathe PINACHO SC-250x1000


          • Mager & Wedemeyer
          • Europaallee 24a
          • 28309 Bremen
          • Deutschland

          • +49 (0)421 - 33616-100
            +49 (0)421 - 33616-169
          • jhagedorn@mager-wedemeyer.com
            www.mager-wedemeyer.com
          #1023-09211F · Center Lathe

          PINACHO - SC-250x1000 - - 2017 -

          Technical details
          turning diameter over bed 502 mm︱turning diameter over slide rest 310 mm︱turning length 1000 mm︱centre height 250 mm︱swing diameter over bed slide 440 mm︱bed width 300 mm︱upper slide travel cross 250 mm︱travel of upper support 130 mm︱spindle nose DIN 55026 Form A ︱spindle bore 58 mm︱transmission ratio 3 ︱spindle turning speed - stepless 40-2300 U/min︱tailstock quill taper MT 4 ︱tailstock quill diameter 68 mm︱tailstock quill adjustment 200 mm︱main drive 5,5 kW︱coolant pump 0,1 kW︱turning tool - shaft cross cut 25 x 25 mm︱3-axis digital readout FAGOR Innova 30iT ︱total power requirement ca. 5,8 kW︱
            turning diameter over bed 502 mm
            turning diameter over slide rest 310 mm
            turning length 1000 mm
            centre height 250 mm
            swing diameter over bed slide 440 mm
            bed width 300 mm
            upper slide travel cross 250 mm
            travel of upper support 130 mm
            spindle nose DIN 55026 Form A
            spindle bore 58 mm
            transmission ratio 3
            spindle turning speed - stepless 40-2300 U/min
            tailstock quill taper MT 4
            tailstock quill diameter 68 mm
            tailstock quill adjustment 200 mm
            main drive 5,5 kW
            coolant pump 0,1 kW
            turning tool - shaft cross cut 25 x 25 mm
            3-axis digital readout FAGOR Innova 30iT
            total power requirement ca. 5,8 kW
            Description :



        • Mager & Wedemeyer
        • Europaallee 24a
        • 28309 Bremen
        • Deutschland

        • Datasheet
          Request / Contact
          used Machines available immediately Center Lathe PINACHO PINACHO SP/165x750


          • HESSE+CO Maschinenfabrik GesmbH
          • Straße 4 Objekt 8
          • 2351 Wiener Neudorf
          • Österreich

          • +43/2236/638 70-0
            +43/2236/636 62
          • office@hesse-maschinen.com
            https://www.hesse-maschinen.com
          #1069-2014 · Center Lathe

          PINACHO - PINACHO SP/165x750 - - 1999 -

          Technical details
          gebraucht19991676prompt, Zwischenverkauf vSpanien10500 €︱ 1335 mm︱ 750 mm︱ 165 mm︱ 42 mm︱ 175 mm︱ 250 mm︱ DIN55022-5 Nr. 460-2000 (9) 1/min︱ 0.05 - 0.75 mm/U︱ 0.025 - 0.375 mm/U︱ 0.5 - 7.5 mm︱ 60245 mm︱
          3-Jaw chucks Röhm Dm. 300 mm 4-fold steel holder with 4 inserts Chuck protection Cranking length 120 mm Sliding rotary guard with integrated machine lamp Rear chip splashboard Cooling equipment Lead screw and draw screw cover Foot brake User Manual in English COMPLIES WITH GERMAN UVV & AUSTRIAN AMVO
            gebraucht
            1999
            1676
            prompt, Zwischenverkauf v
            Spanien
            10500 €
            1
            335 mm
            750 mm
            165 mm
            42 mm
            175 mm
            250 mm
            DIN55022-5 Nr. 4
            60-2000 (9) 1/min
            0.05 - 0.75 mm/U
            0.025 - 0.375 mm/U
            0.5 - 7.5 mm
            60
            245 mm
            Description :
            3-Jaw chucks Röhm Dm. 300 mm
            4-fold steel holder with 4 inserts
            Chuck protection
            Cranking length 120 mm
            Sliding rotary guard with integrated machine lamp
            Rear chip splashboard
            Cooling equipment
            Lead screw and draw screw cover
            Foot brake
            User Manual in English

            COMPLIES WITH GERMAN UVV & AUSTRIAN AMVO


        • HESSE+CO Maschinenfabrik GesmbH
        • Straße 4 Objekt 8
        • 2351 Wiener Neudorf
        • Österreich

        • Datasheet
          Request / Contact
          used Machines available immediately Center Lathe PINACHO SC 325


          • Harry Vraets Machinery B.V.
          • Gezellenstraat 2
          • 3861RD Nijkerk
          • Niederlande

          • +31 (0)332452145
          • info@vraetsmachinery.com
            www.vraetsmachinery.com
          #2039-12215CM · Center Lathe

          PINACHO - SC 325 - - -

          Technical details
          turning diameter over bed 652 mm︱turning diameter over slide rest 450 mm︱bed width 350 mm︱centre height 325 mm︱centre distance 3000 mm︱turning speeds 30-1700 U/min︱spindle bore 80 mm︱quill travel 220 mm︱turning dia. in gap 910 mm︱length of gap 220 mm︱total power requirement 7,5 kW︱weight of the machine ca. 1,85 t︱dimensions of the machine ca. 2600 x 3125 x 1830 mm︱
            turning diameter over bed 652 mm
            turning diameter over slide rest 450 mm
            bed width 350 mm
            centre height 325 mm
            centre distance 3000 mm
            turning speeds 30-1700 U/min
            spindle bore 80 mm
            quill travel 220 mm
            turning dia. in gap 910 mm
            length of gap 220 mm
            total power requirement 7,5 kW
            weight of the machine ca. 1,85 t
            dimensions of the machine ca. 2600 x 3125 x 1830 mm


        • Harry Vraets Machinery B.V.
        • Gezellenstraat 2
        • 3861RD Nijkerk
        • Niederlande

        • Datasheet
          Request / Contact

          CNC Lathe

          used Machines available immediately CNC Lathe PINACHO STH 500/4000


          • Kraft Werkzeugmaschinen GmbH
          • Wilhelmstraße 20
          • 64589 Stockstadt
          • Deutschland

          • +49 (0) 6158/9999975
          • nr@kraft-werkzeugmaschinen.de
            www.kraft-werkzeugmaschinen.de
          #4019-100258 · CNC Lathe

          PINACHO - STH 500/4000 - - 2017 - FANUC OI TF

          Technical details
          turning diameter 1010 mm︱turning length 4000 mm︱control FANUC OI TF ︱max. swing over slide 718 mm︱bed width 500 mm︱spindle taper A2-15 ︱spindle speeds 0-1400 1/min.︱spindle bore 130 mm︱transmission ratio 2 ︱tailstock quill diameter 120 mm︱tailstock quill stroke 300 mm︱taper of tailstock quill 6 MK︱max. length of work piece 4000 mm︱rapid traverse x/z 10/10 m/min︱power requirement 22 kW︱weight of the machine ca. 9500 kg︱dimensions of the machine ca. 6557x2202x2487 mm︱max. workpiece weight between centers 8600 kg︱automatic tool changer 8-fach ︱CNC controller FANUC OI TF
          New CNC lathe KRAFT ST 500/3000 with FANUC OI TF Made in Europe For more information please see the attached documents
            turning diameter 1010 mm
            turning length 4000 mm
            control FANUC OI TF
            max. swing over slide 718 mm
            bed width 500 mm
            spindle taper A2-15
            spindle speeds 0-1400 1/min.
            spindle bore 130 mm
            transmission ratio 2
            tailstock quill diameter 120 mm
            tailstock quill stroke 300 mm
            taper of tailstock quill 6 MK
            max. length of work piece 4000 mm
            rapid traverse x/z 10/10 m/min
            power requirement 22 kW
            weight of the machine ca. 9500 kg
            dimensions of the machine ca. 6557x2202x2487 mm
            max. workpiece weight between ce. 8600 kg
            automatic tool changer 8-fach
            CNC controller FANUC OI TF
            Description :
            New CNC lathe KRAFT ST 500/3000 with FANUC OI TF

            Made in Europe

            For more information please see the attached documents


        • Kraft Werkzeugmaschinen GmbH
        • Wilhelmstraße 20
        • 64589 Stockstadt
        • Deutschland

        • 140.810 €
          Datasheet
          Request / Contact
          used Machines available immediately CNC Lathe Pinacho ST 180/1000


          • Kraft Werkzeugmaschinen GmbH
          • Wilhelmstraße 20
          • 64589 Stockstadt
          • Deutschland

          • +49 (0) 6158/9999975
          • nr@kraft-werkzeugmaschinen.de
            www.kraft-werkzeugmaschinen.de
          #4019-100219 · CNC Lathe

          Pinacho - ST 180/1000 - - 2017 - Fanuc Oi-TF

          Technical details
          turning diameter 360 mm︱turning length 1000 mm︱control Fanuc Oi-TF ︱turning diameter over bed slide 300 mm︱max. swing over slide 190 mm︱bed width 250 mm︱spindle taper A2-5 ︱spindle speeds 0-4000 1/min.︱spindle bore 42 mm︱tailstock quill diameter 58 mm︱tailstock quill stroke 180 mm︱taper of tailstock quill 4 MK︱max. length of work piece 1000 mm︱rapid traverse x/z 15/12 m/min︱power requirement 7,5 kW︱weight of the machine ca. 1200 kg︱dimensions of the machine ca. 2250x1115x1630 mm︱automatic tool changer 8-fach ︱CNC controller Fanuc Oi-TF ︱CE-design
          New CNC lathe KRAFT ST 285/1000 with Fanuc Oi Mate TD Made in Europe For more information please see the attached documents
            turning diameter 360 mm
            turning length 1000 mm
            control Fanuc Oi-TF
            turning diameter over bed slide 300 mm
            max. swing over slide 190 mm
            bed width 250 mm
            spindle taper A2-5
            spindle speeds 0-4000 1/min.
            spindle bore 42 mm
            tailstock quill diameter 58 mm
            tailstock quill stroke 180 mm
            taper of tailstock quill 4 MK
            max. length of work piece 1000 mm
            rapid traverse x/z 15/12 m/min
            power requirement 7,5 kW
            weight of the machine ca. 1200 kg
            dimensions of the machine ca. 2250x1115x1630 mm
            automatic tool changer 8-fach
            CNC controller Fanuc Oi-TF
            Description :
            New CNC lathe KRAFT ST 285/1000 with Fanuc Oi Mate TD

            Made in Europe

            For more information please see the attached documents


        • Kraft Werkzeugmaschinen GmbH
        • Wilhelmstraße 20
        • 64589 Stockstadt
        • Deutschland

        • Datasheet
          Request / Contact
          used Machines available immediately CNC Lathe PINACHO ST 225/1000


          • Kraft Werkzeugmaschinen GmbH
          • Wilhelmstraße 20
          • 64589 Stockstadt
          • Deutschland

          • +49 (0) 6158/9999975
          • nr@kraft-werkzeugmaschinen.de
            www.kraft-werkzeugmaschinen.de
          #4019-10182 · CNC Lathe

          PINACHO - ST 225/1000 - - 2017 - FANUC OI TF

          Technical details
          turning diameter 450 mm︱turning length 1000 mm︱control FANUC OI TF ︱max. swing over slide 260 mm︱bed width 300 mm︱spindle taper A2-6 ︱spindle speeds 0-3000 1/min.︱spindle bore 65 mm︱transmission ratio 1 ︱tailstock quill diameter 68 mm︱tailstock quill stroke 200 mm︱taper of tailstock quill 4 MK︱max. length of work piece 1000 mm︱rapid traverse x/z 12/15 m/min︱power requirement 9 kW︱weight of the machine ca. 1400 kg︱dimensions of the machine ca. 2800x1215x1750 mm︱automatic tool changer 8-fach ︱CNC controller FANUC OI TF ︱tools 1 Satz
          New CNC lathe KRAFT ST 225/1000 with FANUC 0i mate TD Made in Europe For more information please see the attached documents
            turning diameter 450 mm
            turning length 1000 mm
            control FANUC OI TF
            max. swing over slide 260 mm
            bed width 300 mm
            spindle taper A2-6
            spindle speeds 0-3000 1/min.
            spindle bore 65 mm
            transmission ratio 1
            tailstock quill diameter 68 mm
            tailstock quill stroke 200 mm
            taper of tailstock quill 4 MK
            max. length of work piece 1000 mm
            rapid traverse x/z 12/15 m/min
            power requirement 9 kW
            weight of the machine ca. 1400 kg
            dimensions of the machine ca. 2800x1215x1750 mm
            automatic tool changer 8-fach
            CNC controller FANUC OI TF
            tools 1 Satz
            Description :
            New CNC lathe KRAFT ST 225/1000 with FANUC 0i mate TD

            Made in Europe

            For more information please see the attached documents


        • Kraft Werkzeugmaschinen GmbH
        • Wilhelmstraße 20
        • 64589 Stockstadt
        • Deutschland

        • Datasheet
          Request / Contact
          used Machines available immediately CNC Lathe PINACHO SMART 8-260


          • FIMOTEC
          • 20 RUE AMPERE
          • 67500 HAGUENAU
          • Frankreich

          • +33 (0)388720247
            +33 (0)388936066
          • FIMOTEC@WANADOO.FR
            WWW.FIMOTEC.FR
          #1105-03593 · CNC Lathe

          PINACHO - SMART 8-260 - - 2012 - FAGOR TC 8060

          Technical details
          turning diameter 530 mm︱turning length 1000 mm︱centre height 250 mm︱greates pass round over bed 530 mm︱swing diameter over bed slide 260 mm︱spindle turning speed range 0 BIS..2500 IN 5 STUFEN U/min︱control FAGOR TC 8060 ︱spindle bore 80 mm︱interface RS 232 ︱total power requirement 17 kW︱weight of the machine ca. 3 t︱space requirements approx. LxWxH 3 x 1,6 x 1,72 m︱
          3-jaw chuck dia=250mm 8 fach revolver swarf tank, coolant tank div. accessories cnc FAGOR TC 8060 TAILSTOCK
            turning diameter 530 mm
            turning length 1000 mm
            centre height 250 mm
            greates pass round over bed 530 mm
            swing diameter over bed slide 260 mm
            spindle turning speed range 0 BIS..2500 IN 5 STUFEN U/min
            control FAGOR TC 8060
            spindle bore 80 mm
            interface RS 232
            total power requirement 17 kW
            weight of the machine ca. 3 t
            space requirements approx. LxWxH 3 x 1,6 x 1,72 m
            Description :
            3-jaw chuck dia=250mm
            8 fach revolver
            swarf tank, coolant tank
            div. accessories
            cnc FAGOR TC 8060
            TAILSTOCK


        • FIMOTEC
        • 20 RUE AMPERE
        • 67500 HAGUENAU
        • Frankreich

        • Datasheet
          Request / Contact
          used Machines available immediately CNC Lathe PINACHO S 940 C 260/1625


          • IMZ Maschinen Vertriebs GmbH
          • Marie-Curie-Straße 19
          • 73529 Schwäbisch Gmünd
          • Deutschland

          • 0049 (0) 7171 987130
            0049 (0) 7171 9871329
          • info@imz.de
            www.imz.de
          #1075-6449 · CNC Lathe

          PINACHO - S 940 C 260/1625 - - 1997 - FAGOR 800 TG

          Technical details
          turning diameter 520 mm︱turning length 1625 mm︱control FAGOR 800 TG ︱greates pass round over bed 530 mm︱swing diameter over slide rest 475 mm︱centre height 260 mm︱bed width 350 mm︱main spindle bore 68 mm︱turning speeds 1500 U/min︱rapid traverse 5 m/min︱Drive 10 kW︱total power requirement kW︱weight of the machine ca. 1,87 t︱dimensions of the machine ca. 2,8x1,4x1,8 m︱
            turning diameter 520 mm
            turning length 1625 mm
            control FAGOR 800 TG
            greates pass round over bed 530 mm
            swing diameter over slide rest 475 mm
            centre height 260 mm
            bed width 350 mm
            main spindle bore 68 mm
            turning speeds 1500 U/min
            rapid traverse 5 m/min
            Drive 10 kW
            weight of the machine ca. 1,87 t
            dimensions of the machine ca. 2,8x1,4x1,8 m


        • IMZ Maschinen Vertriebs GmbH
        • Marie-Curie-Straße 19
        • 73529 Schwäbisch Gmünd
        • Deutschland

        • Datasheet
          Request / Contact

          Lathe - cycle-controlled

          used Machines available immediately Lathe -  cycle-controlled PINACHO SE/200-42 X 750


          • Kraft Werkzeugmaschinen GmbH
          • Wilhelmstraße 20
          • 64589 Stockstadt
          • Deutschland

          • +49 (0) 6158/9999975
          • nr@kraft-werkzeugmaschinen.de
            www.kraft-werkzeugmaschinen.de
          #4019-100354 · Lathe - cycle-controlled

          PINACHO - SE/200-42 X 750 - - 2020 - FAGOR 8037/Siemens 808D

          Technical details
          turning diameter 402 mm︱turning length 750 mm︱control FAGOR 8037 ︱turning dia. over face-slide 245 mm︱turning diameter over bed slide 380 mm︱bed width 250 mm︱spindle taper A2-5 ︱spindle speeds 40~2800 (3 Stufen) 1/min.︱spindle bore 42 mm︱tailstock quill diameter 58 mm︱tailstock quill stroke 180 mm︱taper of tailstock quill 4 MK︱max. length of work piece 750 mm︱power requirement 4 kW︱weight of the machine ca. 1050 kg︱dimensions of the machine ca. 2000x1115x1670 (LxBxH) mm︱turret 8 fach︱CNC controller FAGOR 8037 ︱European electric ︱coolant system
          New CNC lathe KRAFT ST 285/1000 with Fanuc Oi Mate TD Made in Europe For more information please see the attached documents
            turning diameter 402 mm
            turning length 750 mm
            control FAGOR 8037
            turning dia. over face-slide 245 mm
            turning diameter over bed slide 380 mm
            bed width 250 mm
            spindle taper A2-5
            spindle speeds 40~2800 (3 Stufen) 1/min.
            spindle bore 42 mm
            tailstock quill diameter 58 mm
            tailstock quill stroke 180 mm
            taper of tailstock quill 4 MK
            max. length of work piece 750 mm
            power requirement 4 kW
            weight of the machine ca. 1050 kg
            dimensions of the machine ca. 2000x1115x1670 (LxBxH) mm
            turret 8 fach
            CNC controller FAGOR 8037
            Description :
            New CNC lathe KRAFT ST 285/1000 with Fanuc Oi Mate TD

            Made in Europe

            For more information please see the attached documents


        • Kraft Werkzeugmaschinen GmbH
        • Wilhelmstraße 20
        • 64589 Stockstadt
        • Deutschland

        • Datasheet
          Request / Contact
          used Machines available immediately Lathe -  cycle-controlled PINACHO Smart turn 8 225


          • FIMOTEC
          • 20 RUE AMPERE
          • 67500 HAGUENAU
          • Frankreich

          • +33 (0)388720247
            +33 (0)388936066
          • FIMOTEC@WANADOO.FR
            WWW.FIMOTEC.FR
          #1105-03977 · Lathe - cycle-controlled

          PINACHO - Smart turn 8 225 - - 2013 - FAGOR TC 8055

          Technical details
          turning diameter 450 mm︱turning length 1500 mm︱control FAGOR TC 8055︱total power requirement 15 kW︱weight of the machine ca. 3 t︱dimensions of the machine ca. 2.29X1 X 1.2 m︱
          TEACH IN CNC LATHE Pinacho offers the CNC flat bed lathe ST-225. This is a fast and accurate machine up to 450 mm in swing over bed, 1500 mm in distance between centers and 65 mm in spindle bore. 2 or 3 axis parallel lathes combined with Fagor controL. The available power up to 15 kW in addition to the high rotary speed and low vibrations provided by the servomotor and headstock design make the ST-225 an authentic leader in its category.
            turning diameter 450 mm
            turning length 1500 mm
            control FAGOR TC 8055
            total power requirement 15 kW
            weight of the machine ca. 3 t
            dimensions of the machine ca. 2.29X1 X 1.2 m
            Description :
            TEACH IN CNC LATHE
            Pinacho offers the CNC flat bed lathe ST-225. This is a fast and accurate
            machine up to 450 mm in swing over bed, 1500 mm in distance between centers and
            65 mm in spindle bore. 2 or 3 axis parallel lathes combined with Fagor controL.
            The available power up to 15 kW in addition to the high rotary speed and low
            vibrations provided by the servomotor and headstock design make the ST-225 an
            authentic leader in its category.


        • FIMOTEC
        • 20 RUE AMPERE
        • 67500 HAGUENAU
        • Frankreich

        • Datasheet
          Request / Contact
          used Machines available immediately Lathe -  cycle-controlled PINACHO SM/200


          • ATMH Werkzeugmaschinenhandel GmbH
          • Scharpenbergerstr.96-98
          • 58256 Ennepetal
          • Deutschland

          • +49 (0) 2333 / 403 43 70
            +49 (0) 2333 / 403 43 75
          • info@atmh.de
            www.atmh.de
          #2065-H1116 · Lathe - cycle-controlled

          PINACHO - SM/200 - - 2001 - Fanuc

          Technical details
          turning diameter 420 mm︱turning length 1200 mm︱control Fanuc ︱bore diameter 60 mm︱
            turning diameter 420 mm
            turning length 1200 mm
            control Fanuc
            bore diameter 60 mm
            Description :



        • ATMH Werkzeugmaschinenhandel GmbH
        • Scharpenbergerstr.96-98
        • 58256 Ennepetal
        • Deutschland

        • Datasheet
          Request / Contact
          used Machines available immediately Lathe -  cycle-controlled PINACHO Mustang 200


          • EnTeHa GmbH & Co.KG
          • Im Wollenklingen 6
          • 69517 Gorxheimertal
          • Deutschland

          • +49 6201 2630 545
          • info@enteha.de
            www.enteha.de
          #2081-5197 · Lathe - cycle-controlled

          PINACHO - Mustang 200 - - 2001 - Fagor 8055

          Technical details
          turning diameter 400 mm︱turning length 1000 mm︱control Fagor 8055 ︱total power requirement 11 kW︱weight of the machine ca. 2,2 t︱dimensions of the machine ca. 3,5 x 2 x 2 m︱
            turning diameter 400 mm
            turning length 1000 mm
            control Fagor 8055
            total power requirement 11 kW
            weight of the machine ca. 2,2 t
            dimensions of the machine ca. 3,5 x 2 x 2 m


        • EnTeHa GmbH & Co.KG
        • Im Wollenklingen 6
        • 69517 Gorxheimertal
        • Deutschland

        • Datasheet
          Request / Contact

          Double Column Drawing Press -Hydr.

          used Machines available immediately Double Column Drawing Press -Hydr. MÜLLER ZE 1000-40.3.3


          • VÖGTLE SERVICE GMBH
          • Friedhofstr. 115
          • 73054 Eislingen
          • Deutschland

          • +49 71 61 99 73- 0
            +49 71 61 99 73- 13
          • Thomas.Ruckh@voegtle.de
            www.voegtle.de
          #1050-163054A · Double Column Drawing Press -Hydr.

          MÜLLER - ZE 1000-40.3.3 - - 2005 - Siemens S 7

          Technical details
          Pressure 1000 t︱distance between columns 4100 mm︱stroke 1200 mm︱Distance table/ram, stroke up 2100 mm︱Table surface area 4000 x 2200 mm︱pressure of drawing cushion in table 360 t︱Die cushion stroke in table 300 mm︱Die cushion area in table 3500 x 1600 mm︱Die cushion pressure in ram 100 t︱Die cushion stroke in ram 160 mm︱Die cushion area in ram 3250 x 1600 mm︱Ram surface 4000 x 2200 mm︱Side window 1300 mm︱Oil volume 8000 l︱Power capacity 300,0 kW︱Weight t︱Dimensions (WxDxH) 5,75 x 4,3 x 9,55 m︱Height above floor 7,7 m︱
          year of manufacture 1973 modernization 2005 with oil-hydraulic drive, hydraulic controlled drawing cushion in table and ram, hydraulic cutting impact cushioning stored in dismantled condition Video at seller’s site before dismantling available
            Pressure 1000 t
            distance between columns 4100 mm
            stroke 1200 mm
            Distance table/ram, stroke up 2100 mm
            Table surface area 4000 x 2200 mm
            pressure of drawing cushion in t. 360 t
            Die cushion stroke in table 300 mm
            Die cushion area in table 3500 x 1600 mm
            Die cushion pressure in ram 100 t
            Die cushion stroke in ram 160 mm
            Die cushion area in ram 3250 x 1600 mm
            Ram surface 4000 x 2200 mm
            Side window 1300 mm
            Oil volume 8000 l
            Power capacity 300,0 kW
            Dimensions (WxDxH) 5,75 x 4,3 x 9,55 m
            Height above floor 7,7 m
            Description :
            year of manufacture 1973
            modernization 2005
            with oil-hydraulic drive, hydraulic controlled drawing cushion in table and ram, hydraulic cutting impact cushioning
            stored in dismantled condition
            Video at seller’s site before dismantling available


        • VÖGTLE SERVICE GMBH
        • Friedhofstr. 115
        • 73054 Eislingen
        • Deutschland

        • Datasheet
          Request / Contact
          used Machines available immediately Double Column Drawing Press -Hydr. MÜLLER ZE 600 25.4.1


          • VÖGTLE SERVICE GMBH
          • Friedhofstr. 115
          • 73054 Eislingen
          • Deutschland

          • +49 71 61 99 73- 0
            +49 71 61 99 73- 13
          • Thomas.Ruckh@voegtle.de
            www.voegtle.de
          #1050-163064A · Double Column Drawing Press -Hydr.

          MÜLLER - ZE 600 25.4.1 - - 2005 - Siemens S 7

          Technical details
          Pressure 600 t︱distance between columns 2600 mm︱stroke 900 mm︱Distance table/ram, max. stroke up, adjustment up 1600 mm︱Table surface area 2500 x 1730 mm︱pressure of drawing cushion in table 250 t︱Die cushion stroke in table 400 mm︱Die cushion area in table 2300 x 1300 mm︱Die cushion pressure in ram 63 t︱Die cushion stroke in ram 160 mm︱Die cushion area in ram 1900 x 1300 mm︱Ram surface 2500 x 1730 mm︱Side window 1100 mm︱Oil volume 3500 l︱Power capacity 200,0 kW︱Weight t︱Dimensions (WxDxH) 4,1 x 2,8 x 9,6 m︱Height above floor 6,4 m︱
          year of manufacture 1974 overhaul 2005: complete new electrical cabinet with control Siemens S7 and safety control Pilz with oil-hydraulic drive, hydraulic controlled drawing cushion in table and ram, hydraulic cutting impact cushioning stored in dismantled condition - Video at seller’s site before dismantling available
            Pressure 600 t
            distance between columns 2600 mm
            stroke 900 mm
            Distance table/ram, max. stroke . 1600 mm
            Table surface area 2500 x 1730 mm
            pressure of drawing cushion in t. 250 t
            Die cushion stroke in table 400 mm
            Die cushion area in table 2300 x 1300 mm
            Die cushion pressure in ram 63 t
            Die cushion stroke in ram 160 mm
            Die cushion area in ram 1900 x 1300 mm
            Ram surface 2500 x 1730 mm
            Side window 1100 mm
            Oil volume 3500 l
            Power capacity 200,0 kW
            Dimensions (WxDxH) 4,1 x 2,8 x 9,6 m
            Height above floor 6,4 m
            Description :
            year of manufacture 1974
            overhaul 2005: complete new electrical cabinet with control Siemens S7 and safety control Pilz
            with oil-hydraulic drive, hydraulic controlled drawing cushion in table and ram, hydraulic cutting impact cushioning
            stored in dismantled condition - Video at seller’s site before dismantling available


        • VÖGTLE SERVICE GMBH
        • Friedhofstr. 115
        • 73054 Eislingen
        • Deutschland

        • Datasheet
          Request / Contact
          used Machines available immediately Double Column Drawing Press -Hydr. MÜLLER BZE 800-25.3.1


          • VÖGTLE SERVICE GMBH
          • Friedhofstr. 115
          • 73054 Eislingen
          • Deutschland

          • +49 71 61 99 73- 0
            +49 71 61 99 73- 13
          • Thomas.Ruckh@voegtle.de
            www.voegtle.de
          #1050-163063A · Double Column Drawing Press -Hydr.

          MÜLLER - BZE 800-25.3.1 - - 2005 - Siemens S 7

          Technical details
          Pressure 800 t︱distance between columns 2560 mm︱stroke 1050 mm︱Distance table/ram, stroke up 1870 mm︱Table surface area 2500 x 1730 mm︱pressure of drawing cushion in table 300 t︱Die cushion stroke in table 395 mm︱Die cushion area in table 2300 x 1300 mm︱Ram surface 2500 x 1730 mm︱Die cushion pressure in ram 63 t︱Die cushion stroke in ram 150 mm︱Side window 1000 mm︱Oil volume 4300 l︱Power capacity 200,0 kW︱Weight t︱Dimensions (WxDxH) 4,1 x 2,8 x 10,0 m︱Height above floor 7,0 m︱
          year of manufacture 1974 overhaul 2005 mit ölhydraulischem Antrieb, hydraulischem gesteuertem Ziehkissen im Tisch und Stößel stored in dismantled condition - Video at seller’s site before dismantling available
            Pressure 800 t
            distance between columns 2560 mm
            stroke 1050 mm
            Distance table/ram, stroke up 1870 mm
            Table surface area 2500 x 1730 mm
            pressure of drawing cushion in t. 300 t
            Die cushion stroke in table 395 mm
            Die cushion area in table 2300 x 1300 mm
            Ram surface 2500 x 1730 mm
            Die cushion pressure in ram 63 t
            Die cushion stroke in ram 150 mm
            Side window 1000 mm
            Oil volume 4300 l
            Power capacity 200,0 kW
            Dimensions (WxDxH) 4,1 x 2,8 x 10,0 m
            Height above floor 7,0 m
            Description :
            year of manufacture 1974
            overhaul 2005
            mit ölhydraulischem Antrieb, hydraulischem gesteuertem Ziehkissen im Tisch und Stößel
            stored in dismantled condition - Video at seller’s site before dismantling available


        • VÖGTLE SERVICE GMBH
        • Friedhofstr. 115
        • 73054 Eislingen
        • Deutschland

        • Datasheet
          Request / Contact
          used Machines available immediately Double Column Drawing Press -Hydr. MÜLLER ZE 800-35.2.1


          • VÖGTLE SERVICE GMBH
          • Friedhofstr. 115
          • 73054 Eislingen
          • Deutschland

          • +49 71 61 99 73- 0
            +49 71 61 99 73- 13
          • Thomas.Ruckh@voegtle.de
            www.voegtle.de
          #1050-163069A · Double Column Drawing Press -Hydr.

          MÜLLER - ZE 800-35.2.1 - - 1998 - konventionell

          Technical details
          Pressure 800 t︱distance between columns 3550 mm︱stroke 1100 mm︱Distance table/ram, max. stroke up, adjustment up 1900 mm︱Table surface area 3500 x 1800 mm︱pressure of drawing cushion in table 350 t︱Die cushion stroke in table 280 mm︱Die cushion pressure in ram 80 t︱Die cushion stroke in ram 160 mm︱Ram surface 3500 x 1800 mm︱Side window 1900 mm︱Power capacity kW︱Weight 100,0 t︱Floor Space (WxD) 5,3 x 4,3 m︱Height above floor 7,3 m︱Height below floor 5,0 - 6,0 m︱
          year of manufacture 1970 overhaul 1998 with oil-hydraulic drive, hydraulic controllable drawing cushion in table and ram, hydraulic cutting impact cushioning, moving table (without rails for the moving table) Height beneath floor approx. 5 - 6 m stored in dismantled condition - Video at seller’s site before dismantling available
            Pressure 800 t
            distance between columns 3550 mm
            stroke 1100 mm
            Distance table/ram, max. stroke . 1900 mm
            Table surface area 3500 x 1800 mm
            pressure of drawing cushion in t. 350 t
            Die cushion stroke in table 280 mm
            Die cushion pressure in ram 80 t
            Die cushion stroke in ram 160 mm
            Ram surface 3500 x 1800 mm
            Side window 1900 mm
            Weight 100,0 t
            Floor Space (WxD) 5,3 x 4,3 m
            Height above floor 7,3 m
            Height below floor 5,0 - 6,0 m
            Description :
            year of manufacture 1970
            overhaul 1998
            with oil-hydraulic drive, hydraulic controllable drawing cushion in table and ram, hydraulic cutting impact cushioning, moving table (without rails for the moving table)
            Height beneath floor approx. 5 - 6 m
            stored in dismantled condition - Video at seller’s site before dismantling available


        • VÖGTLE SERVICE GMBH
        • Friedhofstr. 115
        • 73054 Eislingen
        • Deutschland

        • Datasheet
          Request / Contact
          used Machines available immediately Double Column Drawing Press -Hydr. MÜLLER ZE 1500.50.4.1


          • VÖGTLE SERVICE GMBH
          • Friedhofstr. 115
          • 73054 Eislingen
          • Deutschland

          • +49 71 61 99 73- 0
            +49 71 61 99 73- 13
          • Thomas.Ruckh@voegtle.de
            www.voegtle.de
          #1050-203030V · Double Column Drawing Press -Hydr.

          MÜLLER - ZE 1500.50.4.1 - - 1993 - konventionell

          Technical details
          Pressure 1500 t︱distance between columns 5050 mm︱stroke 1100 mm︱Distance table/ram, stroke up 2300 mm︱Table surface area 5000 x 2700 mm︱pressure of drawing cushion in table 320 t︱Die cushion stroke in table 300 mm︱Die cushion area in table 4300 x 1830 mm︱Die cushion pressure in ram 120 t︱Die cushion stroke in ram 200 mm︱Die cushion area in ram 3410 x 1650 mm︱Ram surface 5000 x 2400 mm︱Speed down 360 mm/s︱Speed up 168 - 505 mm/s︱Working speed 19 - 86 mm/s︱Oil volume 10500 l︱Power capacity 450,0 kW︱Weight 400,0 t︱Dimensions (WxDxH) 3,47 x 6,95 x 12,21 m︱Height above floor 8,21 m︱
          year of manufacture 1983 overhaul 1993 with oilhydraulic drive, drawing cushion in table, drawing cushion in ram (drawing cushion surface) approx. 3410 x 1650 mm), cutting impact cushioning, controllabel dependant on pressure/time and way machine can be inspected under power as is where is, WITHOUT dismantling, WITHOUT loading
            Pressure 1500 t
            distance between columns 5050 mm
            stroke 1100 mm
            Distance table/ram, stroke up 2300 mm
            Table surface area 5000 x 2700 mm
            pressure of drawing cushion in t. 320 t
            Die cushion stroke in table 300 mm
            Die cushion area in table 4300 x 1830 mm
            Die cushion pressure in ram 120 t
            Die cushion stroke in ram 200 mm
            Die cushion area in ram 3410 x 1650 mm
            Ram surface 5000 x 2400 mm
            Speed down 360 mm/s
            Speed up 168 - 505 mm/s
            Working speed 19 - 86 mm/s
            Oil volume 10500 l
            Power capacity 450,0 kW
            Weight 400,0 t
            Dimensions (WxDxH) 3,47 x 6,95 x 12,21 m
            Height above floor 8,21 m
            Description :
            year of manufacture 1983
            overhaul 1993
            with oilhydraulic drive, drawing cushion in table, drawing cushion in ram (drawing cushion surface) approx. 3410 x 1650 mm), cutting impact cushioning, controllabel dependant on pressure/time and way
            machine can be inspected under power
            as is where is, WITHOUT dismantling, WITHOUT loading


        • VÖGTLE SERVICE GMBH
        • Friedhofstr. 115
        • 73054 Eislingen
        • Deutschland

        • Datasheet
          Request / Contact
          used Machines available immediately Double Column Drawing Press -Hydr. MÜLLER KEZ 315-16/6.5.1 (UVV)


          • Amann Werkzeugmaschinen GmbH
          • Landshuter Straße 1
          • 85716 Unterschleißheim
          • Deutschland

          • (0049) 89 317754 0
            (0049) 89 3174262
          • info@amann-wzm.de
            www.amann-wzm.de
          #1006-15647 · Double Column Drawing Press -Hydr.

          MÜLLER - KEZ 315-16/6.5.1 (UVV) - - 1983 -

          Technical details
          pressure 315 t︱distance between columns 1620 mm︱stroke 600 mm︱distance table/ram, max. stroke up, adjustment up 1000 mm︱table surface area 1600 x 1100 mm︱pressure of drawing cushion in ram 20 t︱stroke of drawing cushion in ram 100 mm︱drawing cushion surface in pusher 300 x 300 mm︱side window 600 x 1100 mm︱table height over floor 750 mm︱ram surface 1600 x 1100 mm︱oil volume 1500 l︱height over floor 5,05 mm︱height over floor 0,45 mm︱power requirement 110 kW︱weight 35,0 t︱dimensions (WxDxH) 4,65 x 2,61 x 5,50 m︱
          unser Listenpreis versteht sich inklusive Inbetriebnahme der Maschine in unserem Lager, sowie Demonstration der Lauffunktionen ohne Werkzeug, im Übrigen wie die Presse steht und liegt, frei LKW verladen mit ölhydr. Antrieb, hydr. und elektr. Steuerung nach UVV, KEIN! Ziehkissen im Tisch, hydr. Ziehkissen im Stößel, obere und untere Hubbegrenzung, druck-, zeit- und wegabhängig steuerbar, pneum. Stößelverriegelung, hydr. Schnittschlagdämpfung, Zweihandbedienung, Schaltschrank
            pressure 315 t
            distance between columns 1620 mm
            stroke 600 mm
            distance table/ram, max. stroke . 1000 mm
            table surface area 1600 x 1100 mm
            pressure of drawing cushion in r. 20 t
            stroke of drawing cushion in ram 100 mm
            drawing cushion surface in pushe. 300 x 300 mm
            side window 600 x 1100 mm
            table height over floor 750 mm
            ram surface 1600 x 1100 mm
            oil volume 1500 l
            height over floor 5,05 mm
            height over floor 0,45 mm
            power requirement 110 kW
            weight 35,0 t
            dimensions (WxDxH) 4,65 x 2,61 x 5,50 m
            Description :
            unser Listenpreis versteht sich inklusive Inbetriebnahme der Maschine in unserem Lager, sowie Demonstration der Lauffunktionen ohne Werkzeug, im Übrigen wie die Presse steht und liegt, frei LKW verladen
            mit ölhydr. Antrieb, hydr. und elektr. Steuerung nach UVV, KEIN! Ziehkissen im Tisch, hydr. Ziehkissen im Stößel, obere und untere Hubbegrenzung, druck-, zeit- und wegabhängig steuerbar, pneum. Stößelverriegelung, hydr. Schnittschlagdämpfung, Zweihandbedienung, Schaltschrank


        • Amann Werkzeugmaschinen GmbH
        • Landshuter Straße 1
        • 85716 Unterschleißheim
        • Deutschland

        • Datasheet
          Request / Contact
          used Machines available immediately Double Column Drawing Press -Hydr. MÜLLER ZE 600 25.4.2


          • Amann Werkzeugmaschinen GmbH
          • Landshuter Straße 1
          • 85716 Unterschleißheim
          • Deutschland

          • (0049) 89 317754 0
            (0049) 89 3174262
          • info@amann-wzm.de
            www.amann-wzm.de
          #1006-17171 · Double Column Drawing Press -Hydr.

          MÜLLER - ZE 600 25.4.2 - - 1974 -

          Technical details
          pressure 600 t︱distance between columns 2600 mm︱stroke 900 mm︱distance table/blankh.,max. stroke up,adjustm. up 1600 mm︱table surface area 2500 x 1730 mm︱die-cushion pressure inside the table 250 t︱stroke of drawing cushion in table 400 mm︱die-cushion pressure in pusher 63 t︱stroke of drawing cushion in pusher 150 mm︱ram surface 2500 x 1730 mm︱column travel -side 1100 mm︱die-cushion inside the table hydraulic, controlled ︱die-cushion in pusher hydraulic, controlled ︱total power requirement kW︱weight of the machine ca. t︱dimensions of the machine ca. m︱
          overhauled in 2005
            pressure 600 t
            distance between columns 2600 mm
            stroke 900 mm
            distance table/blankh.,max. stro. 1600 mm
            table surface area 2500 x 1730 mm
            die-cushion pressure inside the . 250 t
            stroke of drawing cushion in tab. 400 mm
            die-cushion pressure in pusher 63 t
            stroke of drawing cushion in pus. 150 mm
            ram surface 2500 x 1730 mm
            column travel -side 1100 mm
            die-cushion inside the table hydraulic, controlled
            die-cushion in pusher hydraulic, controlled
            Description :
            overhauled in 2005


        • Amann Werkzeugmaschinen GmbH
        • Landshuter Straße 1
        • 85716 Unterschleißheim
        • Deutschland

        • Datasheet
          Request / Contact
          used Machines available immediately Double Column Drawing Press -Hydr. MÜLLER ZE 600 25.4.3


          • Amann Werkzeugmaschinen GmbH
          • Landshuter Straße 1
          • 85716 Unterschleißheim
          • Deutschland

          • (0049) 89 317754 0
            (0049) 89 3174262
          • info@amann-wzm.de
            www.amann-wzm.de
          #1006-17172 · Double Column Drawing Press -Hydr.

          MÜLLER - ZE 600 25.4.3 - - 1974 -

          Technical details
          pressure 600 t︱distance between columns 2600 mm︱stroke 900 mm︱distance table/blankh.,max. stroke up,adjustm. up 1600 mm︱table surface area 2500 x 1730 mm︱die-cushion pressure inside the table 250 t︱stroke of drawing cushion in table 400 mm︱die-cushion pressure in pusher 63 t︱stroke of drawing cushion in pusher 150 mm︱ram surface 2500 x 1730 mm︱column travel -side 1100 mm︱die-cushion inside the table hydraulic, controlled ︱die-cushion in pusher hydraulic, controlled ︱total power requirement kW︱weight of the machine ca. t︱dimensions of the machine ca. m︱
          overhauled in 2005
            pressure 600 t
            distance between columns 2600 mm
            stroke 900 mm
            distance table/blankh.,max. stro. 1600 mm
            table surface area 2500 x 1730 mm
            die-cushion pressure inside the . 250 t
            stroke of drawing cushion in tab. 400 mm
            die-cushion pressure in pusher 63 t
            stroke of drawing cushion in pus. 150 mm
            ram surface 2500 x 1730 mm
            column travel -side 1100 mm
            die-cushion inside the table hydraulic, controlled
            die-cushion in pusher hydraulic, controlled
            Description :
            overhauled in 2005


        • Amann Werkzeugmaschinen GmbH
        • Landshuter Straße 1
        • 85716 Unterschleißheim
        • Deutschland

        • Datasheet
          Request / Contact
          used Machines available immediately Double Column Drawing Press -Hydr. MÜLLER ZE 600 25.4.4


          • Amann Werkzeugmaschinen GmbH
          • Landshuter Straße 1
          • 85716 Unterschleißheim
          • Deutschland

          • (0049) 89 317754 0
            (0049) 89 3174262
          • info@amann-wzm.de
            www.amann-wzm.de
          #1006-17173 · Double Column Drawing Press -Hydr.

          MÜLLER - ZE 600 25.4.4 - - 1974 -

          Technical details
          pressure 600 t︱distance between columns 2600 mm︱stroke 900 mm︱distance table/blankh.,max. stroke up,adjustm. up 1600 mm︱table surface area 2500 x 1730 mm︱die-cushion pressure inside the table 250 t︱stroke of drawing cushion in table 400 mm︱die-cushion pressure in pusher 63 t︱stroke of drawing cushion in pusher 150 mm︱ram surface 2500 x 1730 mm︱column travel -side 1100 mm︱die-cushion inside the table hydraulic, controlled ︱die-cushion in pusher hydraulic, controlled ︱total power requirement kW︱weight of the machine ca. t︱dimensions of the machine ca. m︱
          overhauled in 2005
            pressure 600 t
            distance between columns 2600 mm
            stroke 900 mm
            distance table/blankh.,max. stro. 1600 mm
            table surface area 2500 x 1730 mm
            die-cushion pressure inside the . 250 t
            stroke of drawing cushion in tab. 400 mm
            die-cushion pressure in pusher 63 t
            stroke of drawing cushion in pus. 150 mm
            ram surface 2500 x 1730 mm
            column travel -side 1100 mm
            die-cushion inside the table hydraulic, controlled
            die-cushion in pusher hydraulic, controlled
            Description :
            overhauled in 2005


        • Amann Werkzeugmaschinen GmbH
        • Landshuter Straße 1
        • 85716 Unterschleißheim
        • Deutschland

        • Datasheet
          Request / Contact
          used Machines available immediately Double Column Drawing Press -Hydr. MÜLLER ZE 1000-40.3.2


          • Amann Werkzeugmaschinen GmbH
          • Landshuter Straße 1
          • 85716 Unterschleißheim
          • Deutschland

          • (0049) 89 317754 0
            (0049) 89 3174262
          • info@amann-wzm.de
            www.amann-wzm.de
          #1006-17159 · Double Column Drawing Press -Hydr.

          MÜLLER - ZE 1000-40.3.2 - - 1973 - Siemens S7

          Technical details
          pressure 1000 t︱distance between columns 4150 mm︱stroke 1200 mm︱distance table/blankh.,max. stroke up,adjustm. up 2100 mm︱table surface area 4000 x 2200 mm︱die-cushion pressure inside the table 360 t︱stroke of drawing cushion in table 300 mm︱die-cushion pressure in pusher 100 t︱stroke of drawing cushion in pusher 150 mm︱ram surface 4000 x 2200 mm︱column travel -side 1300 mm︱die-cushion inside the table hydraulic, controlled ︱die-cushion in pusher hydraulic, controlled ︱Cut Shock absorption hydraulic ︱Control Siemens S7 ︱height over floor 7,7 m︱total power requirement 300 kW︱weight of the machine ca. 280 t︱dimensions of the machine ca. 5,75 x 4,3 x 9,55 m︱
          Year of construction 1973 Modernization 2005 with oil-hydraulic drive, hydraulically controlled drawing cushion in the table and Ram, hydraulic cutting impact damping stored dismantled - short video available from the seller before dismantling
            pressure 1000 t
            distance between columns 4150 mm
            stroke 1200 mm
            distance table/blankh.,max. stro. 2100 mm
            table surface area 4000 x 2200 mm
            die-cushion pressure inside the . 360 t
            stroke of drawing cushion in tab. 300 mm
            die-cushion pressure in pusher 100 t
            stroke of drawing cushion in pus. 150 mm
            ram surface 4000 x 2200 mm
            column travel -side 1300 mm
            die-cushion inside the table hydraulic, controlled
            die-cushion in pusher hydraulic, controlled
            Cut Shock absorption hydraulic
            Control Siemens S7
            height over floor 7,7 m
            total power requirement 300 kW
            weight of the machine ca. 280 t
            dimensions of the machine ca. 5,75 x 4,3 x 9,55 m
            Description :
            Year of construction 1973
            Modernization 2005
            with oil-hydraulic drive, hydraulically controlled drawing cushion in the table
            and
            Ram, hydraulic cutting impact damping
            stored dismantled - short video available from the seller before dismantling


        • Amann Werkzeugmaschinen GmbH
        • Landshuter Straße 1
        • 85716 Unterschleißheim
        • Deutschland

        • Datasheet
          Request / Contact
          used Machines available immediately Double Column Drawing Press -Hydr. MÜLLER ZE 1000-40.3.3


          • Amann Werkzeugmaschinen GmbH
          • Landshuter Straße 1
          • 85716 Unterschleißheim
          • Deutschland

          • (0049) 89 317754 0
            (0049) 89 3174262
          • info@amann-wzm.de
            www.amann-wzm.de
          #1006-17160 · Double Column Drawing Press -Hydr.

          MÜLLER - ZE 1000-40.3.3 - - 1973 -

          Technical details
          pressure 1000 t︱distance between columns 4150 mm︱stroke 1200 mm︱distance table/blankh.,max. stroke up,adjustm. up 2100 mm︱table surface area 4000 x 2200 mm︱die-cushion pressure inside the table 360 t︱stroke of drawing cushion in table 300 mm︱die-cushion pressure in pusher 100 t︱stroke of drawing cushion in pusher 150 mm︱ram surface 4000 x 2200 mm︱column travel -side 1300 mm︱die-cushion inside the table hydraulic, controlled ︱die-cushion in pusher hydraulic, controlled ︱Cut Shock absorption hydraulic ︱total power requirement kW︱weight of the machine ca. 280 t︱dimensions of the machine ca. m︱
          The machine was overtaken 1999.
            pressure 1000 t
            distance between columns 4150 mm
            stroke 1200 mm
            distance table/blankh.,max. stro. 2100 mm
            table surface area 4000 x 2200 mm
            die-cushion pressure inside the . 360 t
            stroke of drawing cushion in tab. 300 mm
            die-cushion pressure in pusher 100 t
            stroke of drawing cushion in pus. 150 mm
            ram surface 4000 x 2200 mm
            column travel -side 1300 mm
            die-cushion inside the table hydraulic, controlled
            die-cushion in pusher hydraulic, controlled
            Cut Shock absorption hydraulic
            weight of the machine ca. 280 t
            Description :
            The machine was overtaken 1999.


        • Amann Werkzeugmaschinen GmbH
        • Landshuter Straße 1
        • 85716 Unterschleißheim
        • Deutschland

        • Datasheet
          Request / Contact
          used Machines available immediately Double Column Drawing Press -Hydr. MÜLLER ZE 1000-40.3.5


          • Amann Werkzeugmaschinen GmbH
          • Landshuter Straße 1
          • 85716 Unterschleißheim
          • Deutschland

          • (0049) 89 317754 0
            (0049) 89 3174262
          • info@amann-wzm.de
            www.amann-wzm.de
          #1006-17162 · Double Column Drawing Press -Hydr.

          MÜLLER - ZE 1000-40.3.5 - - 1973 -

          Technical details
          pressure 1000 t︱distance between columns 4150 mm︱stroke 1200 mm︱distance table/blankh.,max. stroke up,adjustm. up 2100 mm︱table surface area 4000 x 2200 mm︱die-cushion pressure inside the table 360 t︱stroke of drawing cushion in table 300 mm︱die-cushion pressure in pusher 100 t︱stroke of drawing cushion in pusher 150 mm︱ram surface 4000 x 2200 mm︱column travel -side 1300 mm︱die-cushion inside the table hydraulic, controlled ︱die-cushion in pusher hydraulic, controlled ︱Cut Shock absorption hydraulic ︱total power requirement kW︱weight of the machine ca. 280 t︱dimensions of the machine ca. m︱
          The machine was overtaken 1999.
            pressure 1000 t
            distance between columns 4150 mm
            stroke 1200 mm
            distance table/blankh.,max. stro. 2100 mm
            table surface area 4000 x 2200 mm
            die-cushion pressure inside the . 360 t
            stroke of drawing cushion in tab. 300 mm
            die-cushion pressure in pusher 100 t
            stroke of drawing cushion in pus. 150 mm
            ram surface 4000 x 2200 mm
            column travel -side 1300 mm
            die-cushion inside the table hydraulic, controlled
            die-cushion in pusher hydraulic, controlled
            Cut Shock absorption hydraulic
            weight of the machine ca. 280 t
            Description :
            The machine was overtaken 1999.


        • Amann Werkzeugmaschinen GmbH
        • Landshuter Straße 1
        • 85716 Unterschleißheim
        • Deutschland

        • Datasheet
          Request / Contact
          •   
          •   
          • 1  
          • 2  
          •   
          •   

          TOP Manufacturer: