,
Europees netwerk van dealers van voorraadhoudende machines

Bitte einen Suchbegriff eingeben - Voer een zoekterm in
Categorie:
    Fabrikant:
      machines:
        Handelaar:

          Injection Moulding

          Machinelist: Injection Moulding


          Injection-moulding machine (rubber)

          used Injection Moulding Injection-moulding machine (rubber) DESMA 968.1000 ZO B900


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-B221112 · Injection-moulding machine (rubber)

          DESMA - 968.1000 ZO B900 - - 2012 -

          Technical details
          clamping force 11000 kN︱injection volume 12500 cm³︱screw diameter -- mm︱platen size 1000 x 1800 mm︱
          Condition: used, Specification: injection moulding machine for rubber - used, in very good condition machine was serviced annually by manufacturer clamping unit: - Euromap (size): 11000-25600 - clamping force: 11.000 kN - size of heating platens L/W/H: 1000 x 1800 x mm - Distance upper- lower plate: 1200 mm - Stroke min.: 630 mm - Max. stroke: 1030 mm Injection unit: - Injection volume max.: 12,500 cm³ - Injection pressure: 2050 bar - Dosing force: 118 kN - Control: Siemens S7 - Connected load: 3x 400 V, 50 Hz, N - Total current: 276 A - Back-up fuse: 300 A - Pump drive: 277 bar - Driving power: 45 kW - Weight approx.: 43.8 t Operating hours approx.: 33,130 hours
            clamping force 11000 kN
            injection volume 12500 cm³
            screw diameter -- mm
            platen size 1000 x 1800 mm
            Description :
            Condition: used,

            Specification: injection moulding machine for rubber
            - used, in very good condition
            machine was serviced annually by manufacturer

            clamping unit:
            - Euromap (size): 11000-25600
            - clamping force: 11.000 kN
            - size of heating platens L/W/H: 1000 x 1800 x mm
            - Distance upper- lower plate: 1200 mm
            - Stroke min.: 630 mm
            - Max. stroke: 1030 mm

            Injection unit:
            - Injection volume max.: 12,500 cm³
            - Injection pressure: 2050 bar
            - Dosing force: 118 kN

            - Control: Siemens S7
            - Connected load: 3x 400 V, 50 Hz, N
            - Total current: 276 A
            - Back-up fuse: 300 A

            - Pump drive: 277 bar
            - Driving power: 45 kW
            - Weight approx.: 43.8 t

            Operating hours approx.: 33,130 hours



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machine (rubber) BOY E35 VV


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-B221102 · Injection-moulding machine (rubber)

          BOY - E35 VV - - 2011 -

          Technical details
          clamping force 350 kN︱injection volume 58,5 cm³︱screw diameter 28 mm︱platen size 260 x 254 mm︱
          Condition: used, Specification: injection moulding machine for TPE - used clamping unit: - clamping unit: vertical - clamping force: 350 kN - opening stroke max.: 300 mm - platen distance max.: 500 mm - Mould installation height min.: 200 mm - Clear width between tie bars: 260 x 254 mm - Ejector stroke max.: 80 mm - Clamping unit: VV - Lift of protective bonnet: 500 mm Injection unit: - Screw diameter: 28 mm - Screw L/D ratio: 18.6 - Screw stroke max.: 95 mm - Injection volume max.: 58.5 cm³ - Injection pressure: 1577 bar - Plasticising flow: 8.6 g/s - Injection flow: 85.5 g/s - Connected load: 3x 400 V, 50 Hz - Max. heating power: 5.8 kW - Drive power: 7,4 kW - Total power: 13,2 kW - Hydraulics: 210 bar (tank 65 litres) - Operating hours approx.: 2.659 hours Dimensions L/W/H approx.: 2,047 x 803 x 2,710 mm Footprint: 1.7 m² Weight approx.: 1,670 kg Last maintenance: 01.2021 Incl. granulate conveyor and temperature control unit.
            clamping force 350 kN
            injection volume 58,5 cm³
            screw diameter 28 mm
            platen size 260 x 254 mm
            Description :
            Condition: used,

            Specification: injection moulding machine for TPE
            - used

            clamping unit:
            - clamping unit: vertical
            - clamping force: 350 kN
            - opening stroke max.: 300 mm
            - platen distance max.: 500 mm
            - Mould installation height min.: 200 mm
            - Clear width between tie bars: 260 x 254 mm
            - Ejector stroke max.: 80 mm
            - Clamping unit: VV
            - Lift of protective bonnet: 500 mm

            Injection unit:
            - Screw diameter: 28 mm
            - Screw L/D ratio: 18.6
            - Screw stroke max.: 95 mm
            - Injection volume max.: 58.5 cm³
            - Injection pressure: 1577 bar
            - Plasticising flow: 8.6 g/s
            - Injection flow: 85.5 g/s

            - Connected load: 3x 400 V, 50 Hz
            - Max. heating power: 5.8 kW
            - Drive power: 7,4 kW
            - Total power: 13,2 kW
            - Hydraulics: 210 bar (tank 65 litres)
            - Operating hours approx.: 2.659 hours

            Dimensions L/W/H approx.: 2,047 x 803 x 2,710 mm
            Footprint: 1.7 m²
            Weight approx.: 1,670 kg
            Last maintenance: 01.2021

            Incl. granulate conveyor and temperature control unit.



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machine (rubber) ENGEL ES 200V/45 VT-Elast


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-B210304 · Injection-moulding machine (rubber)

          ENGEL - ES 200V/45 VT-Elast - - 2010 -

          Technical details
          clamping force 450 kN︱injection volume 99 cm³︱screw diameter 30 mm︱platen size 860 x 320 mm︱closing stroke 406 mm︱
          Condition: used, Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083 Clamping unit: - Clamping force: 450 kN - Opening travel: 406 mm - Heating plate size: 860 x 320 mm - Mould height min.: 264 mm - Max. plate spacing: 464 mm - Ejector stroke: 20 mm - Ejector force: 20 kN Injection unit: - Screw diameter: 30 mm - Screw length L/D: 16 - Dosing stroke: 140 mm - Stroke volume max.: 99 cm³ - Max. spray weight: 114 g - Screw speed: 20 - 300 rpm - Injection flow: 106 cm³/s - Injection flow increased: 71 cm³/s - Special injection pressure: 1451 bar - Spec. injection pressure increased: 2205 bar - Nozzle path: 530 mm - Operating hours: 54716 h - Pump drive power: 11 kW - Weight without oil: 6,500 kg - Dimensions L/W/height: 2,500 x 1,900 x 3,680 mm
            clamping force 450 kN
            injection volume 99 cm³
            screw diameter 30 mm
            platen size 860 x 320 mm
            closing stroke 406 mm
            Description :
            Condition: used,

            Specification: C-Frame Injection Moulding Machine - second-hand
            Serial No.: 45083

            Clamping unit:
            - Clamping force: 450 kN
            - Opening travel: 406 mm
            - Heating plate size: 860 x 320 mm
            - Mould height min.: 264 mm
            - Max. plate spacing: 464 mm
            - Ejector stroke: 20 mm
            - Ejector force: 20 kN


            Injection unit:
            - Screw diameter: 30 mm
            - Screw length L/D: 16
            - Dosing stroke: 140 mm
            - Stroke volume max.: 99 cm³
            - Max. spray weight: 114 g
            - Screw speed: 20 - 300 rpm
            - Injection flow: 106 cm³/s
            - Injection flow increased: 71 cm³/s
            - Special injection pressure: 1451 bar
            - Spec. injection pressure increased: 2205 bar
            - Nozzle path: 530 mm
            - Operating hours: 54716 h
            - Pump drive power: 11 kW
            - Weight without oil: 6,500 kg
            - Dimensions L/W/height: 2,500 x 1,900 x 3,680 mm



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machine (rubber) LWB STEINL VRE 1100/1000t compact


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-B230703 · Injection-moulding machine (rubber)

          LWB STEINL - VRE 1100/1000t compact - - 2008-2010 -

          Technical details
          clamping force 1100 kN︱injection volume 1000 cm³︱screw diameter -- mm︱platen size 330 x 500 mm︱
          Condition: used, Specification: frame injection moulding machine - used clamping unit: - clamping force: 1100 kN - heating platen size: 330 x 500 mm - mould size: 500 x 400 mm - Clear width upper- lower platen: 740 mm - Clamping direction: from below Injection unit: - Injection volume max.: 1000 cm³ - Injection: from above - Voltage: 3x 400 V, 50 Hz, N, PE - Control voltage: 24 VDC - Hydraulics Rexroth: 7,5 kW - Control: ECO II / System X20 - Pump capacity: 63 l/min Units are currently still in production and will be available from August. There are 11 identical units, built between 2008 and 2010, available.
            clamping force 1100 kN
            injection volume 1000 cm³
            screw diameter -- mm
            platen size 330 x 500 mm
            Description :
            Condition: used,

            Specification: frame injection moulding machine
            - used

            clamping unit:
            - clamping force: 1100 kN
            - heating platen size: 330 x 500 mm
            - mould size: 500 x 400 mm
            - Clear width upper- lower platen: 740 mm
            - Clamping direction: from below

            Injection unit:
            - Injection volume max.: 1000 cm³
            - Injection: from above
            - Voltage: 3x 400 V, 50 Hz, N, PE
            - Control voltage: 24 VDC
            - Hydraulics Rexroth: 7,5 kW

            - Control: ECO II / System X20
            - Pump capacity: 63 l/min

            Units are currently still in production and will be available from August.
            There are 11 identical units, built between 2008 and 2010, available.



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machine (rubber) REP V38 Y04W


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-B221101 · Injection-moulding machine (rubber)

          REP - V38 Y04W - - 2005 -

          Technical details
          clamping force 1.013 kN︱injection volume 400 cm³︱screw diameter 25 mm︱platen size 335 x 400 mm︱
          Condition: used, Specification: injection moulding machine for rubber - used clamping unit: - clamping unit: vertical - clamping force: 1.013 kN - size of heating platen: 335 x 400 mm (standard) core turning unit Injection unit: - screw diameter: 25 mm - Barrel diameter: 51 mm - Injection volume max.: 400 cm³ - Injection pressure: 1,500 bar - Connection value: 3x 400 V, 50 Hz 42A fuse protection (incl. periphery) - Electrical power: 29,1 kVA - Control: G8 Control - Hydraulics: 250 bar (tank 200 litres) - Further connections: Cooling water inlet/outlet Dimensions L/W/H approx.: 2,300 x 3,400 x 2,250 mm Weight approx.: 2,950 kg Not for sale: Article-specific extensions (demoulding unit, cold runner block with temperature control units) Available as from 01.01.2023
            clamping force 1.013 kN
            injection volume 400 cm³
            screw diameter 25 mm
            platen size 335 x 400 mm
            Description :
            Condition: used,

            Specification: injection moulding machine for rubber
            - used

            clamping unit:
            - clamping unit: vertical
            - clamping force: 1.013 kN
            - size of heating platen: 335 x 400 mm
            (standard) core turning unit

            Injection unit:
            - screw diameter: 25 mm
            - Barrel diameter: 51 mm
            - Injection volume max.: 400 cm³
            - Injection pressure: 1,500 bar

            - Connection value: 3x 400 V, 50 Hz
            42A fuse protection (incl. periphery)
            - Electrical power: 29,1 kVA
            - Control: G8 Control
            - Hydraulics: 250 bar (tank 200 litres)
            - Further connections: Cooling water inlet/outlet

            Dimensions L/W/H approx.: 2,300 x 3,400 x 2,250 mm
            Weight approx.: 2,950 kg

            Not for sale: Article-specific extensions
            (demoulding unit, cold runner block with temperature control units)
            Available as from 01.01.2023



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machine (rubber) ENGEL ES 200/45 VTHL


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-B210803 · Injection-moulding machine (rubber)

          ENGEL - ES 200/45 VTHL - - 2004 -

          Technical details
          clamping force 450 kN︱injection volume 135 cm³︱screw diameter 35 mm︱platen size 600 x 400 mm︱
          Condition: used, Specification: C-frame injection moulding machine for TPE - used, from testing department Including PIOVAN dosing unit clamping unit: - clamping force: 450 kN - heating platen size: 600 x 400 mm - Clear width: 585 mm - Tool installation height min.: 185 mm - Max. stroke: 400 mm - sliding table: yes - Clamping direction: from below - Ejector / lifter: Up + Lo - Number of core pulls: 4 - Ejector stroke: 200 mm Injection unit: - Injection volume max.: 135 cm³ - Screw diameter: 35 mm - Connected load: 3x 400 V, 50 Hz - Weight approx.: 5,500 kg
            clamping force 450 kN
            injection volume 135 cm³
            screw diameter 35 mm
            platen size 600 x 400 mm
            Description :
            Condition: used,

            Specification: C-frame injection moulding machine for TPE
            - used, from testing department

            Including PIOVAN dosing unit

            clamping unit:
            - clamping force: 450 kN
            - heating platen size: 600 x 400 mm
            - Clear width: 585 mm
            - Tool installation height min.: 185 mm
            - Max. stroke: 400 mm
            - sliding table: yes
            - Clamping direction: from below
            - Ejector / lifter: Up + Lo
            - Number of core pulls: 4
            - Ejector stroke: 200 mm

            Injection unit:
            - Injection volume max.: 135 cm³
            - Screw diameter: 35 mm

            - Connected load: 3x 400 V, 50 Hz
            - Weight approx.: 5,500 kg



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machine (rubber) ENGEL ES 200/25 VHL


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-B220302 · Injection-moulding machine (rubber)

          ENGEL - ES 200/25 VHL - - 2003 -

          Technical details
          clamping force 250 kN︱injection volume 49 cm³︱screw diameter 25 mm︱platen size 300 x 300 mm︱
          Condition: used, specification: C-frame injection moulding machine - used clamping unit: - clamping force: 250 kN - heating platen size: 300 x 300 mm - clamping/opening stroke: 330 mm - Closing direction: from below - Lateral ejector: yes - Ejector stroke/force: 115 mm / 12 kN Injection unit: - Injection volume max.: 49 cm³ - Screw diameter: 25 mm - Screw length: 16 - Screw speed max.: 250 rpm - Injection: from above - Voltage: 3x 400 V, 50 Hz, N, PE - Connected load: 55 kW/92 A - Weight approx.: 3,500 kg Various accessories are also available: - Injection unit (25 screw) - 2 heating plates - Funnel and various small parts
            clamping force 250 kN
            injection volume 49 cm³
            screw diameter 25 mm
            platen size 300 x 300 mm
            Description :
            Condition: used,

            specification: C-frame injection moulding machine
            - used

            clamping unit:
            - clamping force: 250 kN
            - heating platen size: 300 x 300 mm
            - clamping/opening stroke: 330 mm
            - Closing direction: from below
            - Lateral ejector: yes
            - Ejector stroke/force: 115 mm / 12 kN

            Injection unit:
            - Injection volume max.: 49 cm³
            - Screw diameter: 25 mm
            - Screw length: 16
            - Screw speed max.: 250 rpm
            - Injection: from above
            - Voltage: 3x 400 V, 50 Hz, N, PE
            - Connected load: 55 kW/92 A

            - Weight approx.: 3,500 kg

            Various accessories are also available:
            - Injection unit (25 screw)
            - 2 heating plates
            - Funnel and various small parts



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machine (rubber) ARBURG 520 C 1300-350


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-B220801 · Injection-moulding machine (rubber)

          ARBURG - 520 C 1300-350 - - 2001 -

          Technical details
          clamping force 1.300 kN︱injection volume 230 cm³︱screw diameter 45 mm︱platen size 685 x 685 mm︱
          Condition: used, Specification: injection moulding machine for TPE - used including Koch dosing unit clamping unit: - clamping force: 1.300 kN - heating platen size: 685 x 685 mm - Clear distance between tie bars: 470 x 470 mm - Mould installation height min.: 250 mm - Distance between platens max.: 900 mm - Opening stroke max.: 650 mm - Ejector stroke: 225 mm Injection unit: - Screw diameter: 45 mm x 18D - Injection volume max.: 230 cm³ - Injection part weight: 210 g/hp - Max. injection pressure: 1,670 bar - Screw circumferential speed: 75 m/min - Cylinder heating: 4x 2,200 W - Nozzle heating: 600 W - Connection value: 3x 400 V, 50 Hz - Electrical connection (back-up fuse): 100 A - Weight approx.: 6,380 kg - Oil filling: 260 litres - Operating hours approx.: 64,903 h
            clamping force 1.300 kN
            injection volume 230 cm³
            screw diameter 45 mm
            platen size 685 x 685 mm
            Description :
            Condition: used,

            Specification: injection moulding machine for TPE
            - used

            including Koch dosing unit

            clamping unit:
            - clamping force: 1.300 kN
            - heating platen size: 685 x 685 mm
            - Clear distance between tie bars: 470 x 470 mm
            - Mould installation height min.: 250 mm
            - Distance between platens max.: 900 mm
            - Opening stroke max.: 650 mm
            - Ejector stroke: 225 mm

            Injection unit:
            - Screw diameter: 45 mm x 18D
            - Injection volume max.: 230 cm³
            - Injection part weight: 210 g/hp
            - Max. injection pressure: 1,670 bar
            - Screw circumferential speed: 75 m/min
            - Cylinder heating: 4x 2,200 W
            - Nozzle heating: 600 W

            - Connection value: 3x 400 V, 50 Hz
            - Electrical connection (back-up fuse): 100 A
            - Weight approx.: 6,380 kg
            - Oil filling: 260 litres
            - Operating hours approx.: 64,903 h




        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machine (rubber) ENGEL ES 200V/45 VT-Elast


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-B210303 · Injection-moulding machine (rubber)

          ENGEL - ES 200V/45 VT-Elast - - 2001 -

          Technical details
          clamping force 450 kN︱injection volume 99 cm³︱screw diameter 30 mm︱platen size 860 x 320 mm︱closing stroke 406 mm︱
          Condition: used, Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083 Clamping unit: - Clamping force: 450 kN - Opening travel: 406 mm - Heating plate size: 860 x 320 mm - Mould height min.: 264 mm - Max. plate spacing: 464 mm - Ejector stroke: 20 mm - Ejector force: 20 kN Injection unit: - Screw diameter: 30 mm - Screw length L/D: 17 - Dosing stroke: 140 mm - Stroke volume max.: 99 cm³ - Max. spray weight: 114 g - Screw speed: 20 - 300 rpm - Injection flow: 106 cm³/s - Injection flow increased: 71 cm³/s - Special injection pressure: 1450 bar - Spec. injection pressure increased: 2210 bar - Nozzle path: 200 mm - Operating hours: 54716 h - Pump drive power: 15 kW - Weight without oil: 5,500 kg - Dimensions L/W/height: 2,500 x 1,900 x 3,680 mm
            clamping force 450 kN
            injection volume 99 cm³
            screw diameter 30 mm
            platen size 860 x 320 mm
            closing stroke 406 mm
            Description :
            Condition: used,

            Specification: C-Frame Injection Moulding Machine - second-hand
            Serial No.: 45083

            Clamping unit:
            - Clamping force: 450 kN
            - Opening travel: 406 mm
            - Heating plate size: 860 x 320 mm
            - Mould height min.: 264 mm
            - Max. plate spacing: 464 mm
            - Ejector stroke: 20 mm
            - Ejector force: 20 kN


            Injection unit:
            - Screw diameter: 30 mm
            - Screw length L/D: 17
            - Dosing stroke: 140 mm
            - Stroke volume max.: 99 cm³
            - Max. spray weight: 114 g
            - Screw speed: 20 - 300 rpm
            - Injection flow: 106 cm³/s
            - Injection flow increased: 71 cm³/s
            - Special injection pressure: 1450 bar
            - Spec. injection pressure increased: 2210 bar
            - Nozzle path: 200 mm
            - Operating hours: 54716 h
            - Pump drive power: 15 kW
            - Weight without oil: 5,500 kg
            - Dimensions L/W/height: 2,500 x 1,900 x 3,680 mm



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machine (rubber) ARBURG 270 M 350-90


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-B230201 · Injection-moulding machine (rubber)

          ARBURG - 270 M 350-90 - - 1996 -

          Technical details
          clamping force 350 kN︱injection volume 59 cm³︱screw diameter 25 mm︱platen size 400 x 400 mm︱
          Condition: used, Specification: injection moulding machine for rubber - used International size: 350-90 clamping unit: - clamping force: 350 kN - clamping platen size: 400 x 400 mm - Clear distance between tie bars: 270 x 270 mm - Mould installation height min.: 225 mm - Distance between clamping platens: max. 550 mm - Opening stroke max.: 325 mm - Ejector stroke: 125 mm Injection unit: - Screw diameter: 25 mm x 20D - Injection volume max.: 49 cm³ - Injection part weight: 59 g/hp - Max. injection pressure: 1,860 bar - Screw circumferential speed: 37 m/min - Cylinder heating: 4x 900 W - Nozzle heating: 300 W - Heating complete: 4,6 kW - Pump motor: 11 kW - Total power: 15,6 kW - Connection value: 3x 400 V, 50 Hz - Electrical connection (pre-fuse): 50 A - Weight approx.: 1,650 kg - Oil filling: 190 litres - Switch cabinet: 150 kg - Operating hours approx.: 1,100 h
            clamping force 350 kN
            injection volume 59 cm³
            screw diameter 25 mm
            platen size 400 x 400 mm
            Description :
            Condition: used,

            Specification: injection moulding machine for rubber
            - used

            International size: 350-90

            clamping unit:
            - clamping force: 350 kN
            - clamping platen size: 400 x 400 mm
            - Clear distance between tie bars: 270 x 270 mm
            - Mould installation height min.: 225 mm
            - Distance between clamping platens: max. 550 mm
            - Opening stroke max.: 325 mm
            - Ejector stroke: 125 mm

            Injection unit:
            - Screw diameter: 25 mm x 20D
            - Injection volume max.: 49 cm³
            - Injection part weight: 59 g/hp
            - Max. injection pressure: 1,860 bar
            - Screw circumferential speed: 37 m/min
            - Cylinder heating: 4x 900 W
            - Nozzle heating: 300 W
            - Heating complete: 4,6 kW
            - Pump motor: 11 kW
            - Total power: 15,6 kW

            - Connection value: 3x 400 V, 50 Hz
            - Electrical connection (pre-fuse): 50 A
            - Weight approx.: 1,650 kg
            - Oil filling: 190 litres
            - Switch cabinet: 150 kg
            - Operating hours approx.: 1,100 h



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machine (rubber) ENGEL ES 330/80 LIM


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-B230701 · Injection-moulding machine (rubber)

          ENGEL - ES 330/80 LIM - - 1993 -

          Technical details
          clamping force 800 kN︱injection volume 78 cm³︱screw diameter 25 mm︱platen size 570 x 552 mm︱
          Condition: used, Specification: injection moulding machine for LSR - used Nr. 13EN08 clamping unit: - clamping force: 800 kN - size of heating platen: 570 x 552 mm - Between tie bars horizontally: 405 mm - Between tie bars vertically: 345 mm - Opening stroke: 310 mm - Ejector force: 25.4 kN - Ejector stroke: 100 mm - Mould installation height max.: 530 mm - Mould installation height min.: 250 mm - Bar diameter: 60 mm - Control: CC 90-A0 Injection unit: - Injection volume max.: 78 cm³ - Injection weight max.: 90 g - Screw diameter: 25 mm - Metering stroke: 160 mm - Screw speed max.: 20 - 400 rpm - Injection flow: 87 g/sec - Injection flow (increased): 64 g/sec - Specific injection pressure: 2400 bar - Nozzle stroke: 250 mm - Nozzle contact pressure: 47 kN Drive: - Voltage: 3x 400 V, 50 Hz, N, PE - Pump drive power: 15 kW - Oil filling: 185 l - Weight approx.: 4.000 kg
            clamping force 800 kN
            injection volume 78 cm³
            screw diameter 25 mm
            platen size 570 x 552 mm
            Description :
            Condition: used,

            Specification: injection moulding machine for LSR
            - used
            Nr. 13EN08

            clamping unit:
            - clamping force: 800 kN
            - size of heating platen: 570 x 552 mm
            - Between tie bars horizontally: 405 mm
            - Between tie bars vertically: 345 mm
            - Opening stroke: 310 mm
            - Ejector force: 25.4 kN
            - Ejector stroke: 100 mm
            - Mould installation height max.: 530 mm
            - Mould installation height min.: 250 mm
            - Bar diameter: 60 mm

            - Control: CC 90-A0

            Injection unit:
            - Injection volume max.: 78 cm³
            - Injection weight max.: 90 g
            - Screw diameter: 25 mm
            - Metering stroke: 160 mm
            - Screw speed max.: 20 - 400 rpm
            - Injection flow: 87 g/sec
            - Injection flow (increased): 64 g/sec
            - Specific injection pressure: 2400 bar
            - Nozzle stroke: 250 mm
            - Nozzle contact pressure: 47 kN

            Drive:
            - Voltage: 3x 400 V, 50 Hz, N, PE
            - Pump drive power: 15 kW
            - Oil filling: 185 l
            - Weight approx.: 4.000 kg



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machine (rubber) ENGEL ES 330/80 LIM


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-B230702 · Injection-moulding machine (rubber)

          ENGEL - ES 330/80 LIM - - 1991 -

          Technical details
          clamping force 800 kN︱injection volume 154 cm³︱screw diameter 35 mm︱platen size 570 x 552 mm︱
          Condition: used, Specification: injection moulding machine for LSR - used Nr. 13EN12 clamping unit: - clamping force: 800 kN - size of heating platen: 570 x 552 mm - Between tie bars horizontally: 405 mm - Between tie bars vertically: 345 mm - Opening stroke: 310 mm - Ejector force: 25.4 kN - Ejector stroke: 100 mm - Mould installation height max.: 530 mm - Mould installation height min.: 250 mm - Bar diameter: 60 mm Injection unit: - Injection volume max.: 154 cm³ - Injection weight max.: 156 g - Screw diameter: 35 mm - Metering stroke: 160 mm - Screw speed max.: 20 - 320 rpm - Delivery flow: 35 g/sec - Injection flow: 148 g/sec - Injection flow (increased): 107 g/sec - Specific injection pressure: 1600 bar - Specific injection pressure increased: 2200 bar - Nozzle stroke: 250 mm - Nozzle contact pressure: 47 kN - Control: CC 90-A02 Drive: - Voltage: 3x 400 V, 50 Hz, N, PE - Pump drive power: 15 kW - Oil filling: 155 l - Weight approx.: 3,100 kg
            clamping force 800 kN
            injection volume 154 cm³
            screw diameter 35 mm
            platen size 570 x 552 mm
            Description :
            Condition: used,

            Specification: injection moulding machine for LSR
            - used
            Nr. 13EN12

            clamping unit:
            - clamping force: 800 kN
            - size of heating platen: 570 x 552 mm
            - Between tie bars horizontally: 405 mm
            - Between tie bars vertically: 345 mm
            - Opening stroke: 310 mm
            - Ejector force: 25.4 kN
            - Ejector stroke: 100 mm
            - Mould installation height max.: 530 mm
            - Mould installation height min.: 250 mm
            - Bar diameter: 60 mm

            Injection unit:
            - Injection volume max.: 154 cm³
            - Injection weight max.: 156 g
            - Screw diameter: 35 mm
            - Metering stroke: 160 mm
            - Screw speed max.: 20 - 320 rpm
            - Delivery flow: 35 g/sec
            - Injection flow: 148 g/sec
            - Injection flow (increased): 107 g/sec
            - Specific injection pressure: 1600 bar
            - Specific injection pressure increased: 2200 bar
            - Nozzle stroke: 250 mm
            - Nozzle contact pressure: 47 kN

            - Control: CC 90-A02

            Drive:
            - Voltage: 3x 400 V, 50 Hz, N, PE
            - Pump drive power: 15 kW
            - Oil filling: 155 l
            - Weight approx.: 3,100 kg



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machine (rubber) REMAK-Keil GmbH ESM 30-SP


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-B210301 · Injection-moulding machine (rubber)

          REMAK-Keil GmbH - ESM 30-SP - - 1981 -

          Technical details
          clamping force 300 kN︱injection volume 105 cm³︱screw diameter -- mm︱platen size 300 x 400 mm︱
          Condition: used, Specification: Vertical C-frame Injection Moulding Machine for rubber - second-hand suitable for vulcanising together extruded rubber profiles to sealing frames or for the production of small precision moulded parts. The C-frame design ensures very good mould accessibility accessibility of the tools from three sides, so that when vulcanising the necessary space when vulcanising sealing profiles. to be able to work comfortably even with multiple tools. be able to work comfortably. Injection unit: - Injection volume approx.: 105 cm³ - Injection pressure approx.: 1,800 bar Clamping unit: - Clamping force: 300 kN - Size of heating platen: 300 x 400 mm - Clamping speed: 100 mm/sec - Heating power per platen: 3 kW - Total power with sliding table: 9 kW With alternating sliding table, i.e. two moulds can be used at the same time. two moulds at the same time. - Dimensions approx.: 2.400 x 1.400 x 2.600 mm - Weight approx.: 3,000 kg
            clamping force 300 kN
            injection volume 105 cm³
            screw diameter -- mm
            platen size 300 x 400 mm
            Description :
            Condition: used,

            Specification: Vertical C-frame Injection Moulding Machine
            for rubber - second-hand

            suitable for vulcanising together extruded rubber profiles
            to sealing frames or for the production of small precision
            moulded parts. The C-frame design ensures very good mould accessibility
            accessibility of the tools from three sides, so that when vulcanising
            the necessary space when vulcanising sealing profiles.
            to be able to work comfortably even with multiple tools.
            be able to work comfortably.

            Injection unit:
            - Injection volume approx.: 105 cm³
            - Injection pressure approx.: 1,800 bar

            Clamping unit:
            - Clamping force: 300 kN
            - Size of heating platen: 300 x 400 mm
            - Clamping speed: 100 mm/sec
            - Heating power per platen: 3 kW
            - Total power with sliding table: 9 kW

            With alternating sliding table, i.e. two moulds can be used at the same time.
            two moulds at the same time.

            - Dimensions approx.: 2.400 x 1.400 x 2.600 mm

            - Weight approx.: 3,000 kg



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact

          Injection-moulding machines (plastic)

          used Injection Moulding Injection-moulding machines (plastic) KOCH Maschinentechnik GmbH Foederlanlagen-Steuerung 4-56


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-L230508 · Injection-moulding machines (plastic)

          KOCH Maschinentechnik GmbH - Foederlanlagen-Steuerung 4-56 - - 2017 -

          Technical details
          clamping force -- kN︱injection volume -- cm³︱screw diameter -- mm︱
          Condition: used, specification: conveyor control/material station for 4 up to 56 separators for granulate- Conveying for plastic injection moulding machine, Description: The conveyor system control SM-SPS enables in cooperation with material separators and blowers to feed up to 56 processing machines or material processing machines or material take-off points with one or more materials. several materials. Technical data: - PLC control: Siemens S7-300 - Colour touch panel: SPS4: 6" panel - The control system is designed to control the following components: - 4 -56 separators (also units equipped with level probes and filter cleaning filter cleaning) - Control of the blower or a VAkuumpump - Control of the blower relief valve - Control of a safety filter - Control of empty suction valves - Material recognition via plug, scanner or empty suction valves For further technical data, see excerpt from the operating instructions. Overall scope: - Conveyor system control - Material station with accessories (see pictures/description in the appendix) - Dryer + other accessories (see pictures) - Voltage: 3x 400V, 50/60Hz, N, PE - Control voltage: 24V DC
            clamping force -- kN
            injection volume -- cm³
            screw diameter -- mm
            Description :
            Condition: used,

            specification: conveyor control/material station
            for 4 up to 56 separators for granulate-
            Conveying for plastic injection moulding machine,

            Description:
            The conveyor system control SM-SPS enables in cooperation with
            material separators and blowers to feed up to 56 processing machines or
            material processing machines or material take-off points with one or
            more materials. several materials.

            Technical data:
            - PLC control: Siemens S7-300
            - Colour touch panel: SPS4: 6" panel
            - The control system is designed to control the following components:
            - 4 -56 separators (also units equipped with level probes and filter cleaning
            filter cleaning)
            - Control of the blower or a VAkuumpump
            - Control of the blower relief valve
            - Control of a safety filter
            - Control of empty suction valves
            - Material recognition via plug, scanner or empty suction valves

            For further technical data, see excerpt from the operating instructions.

            Overall scope:
            - Conveyor system control
            - Material station with accessories (see pictures/description in the appendix)
            - Dryer + other accessories (see pictures)

            - Voltage: 3x 400V, 50/60Hz, N, PE
            - Control voltage: 24V DC



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machines (plastic) DEMAG multi 420-810


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-L230506 · Injection-moulding machines (plastic)

          DEMAG - multi 420-810 - - 2008 -

          Technical details
          clamping force 4200 kN︱injection volume 1212 /292 cm³︱screw diameter 70 /15 mm︱platen size 1200 x 1100 mm︱
          Condition: used, Specification: Horizontal 2K-injection moulding machine, DEMAG Multi 420/810-2300h/430 incl. handling injection unit 1: - Screw diameter: 70 mm - injection volume: 1.112 cm³ - weight: 880 g injection unit 2: - Screw diameter: 15 mm - injection volume: 292 cm³ - weight: 190 g Clamping unit: - Clamping force: 1200 kN - Centring: 160 mm - Platen size: 1200 x 1100 mm - Mould size: 810 x 710 mm - Mould thickness min.: 380 mm - Mould thickness max.: 940 mm - 4 & 4 Cascades - 4x core pull - Handling: Yes - Voltage: 3x 400V, 50Hz, N, PE - Total power: 192 kW - Dimensions L/W/H: approx. 7,900 x 2,200 x 5,000 mm - Weight approx.: 25,000 kg Further DEMAG plastic injection moulding machines and a conveyor control/material station for 4 to 56 separators for granulate conveying on our homepage.
            clamping force 4200 kN
            injection volume 1212 /292 cm³
            screw diameter 70 /15 mm
            platen size 1200 x 1100 mm
            Description :
            Condition: used,

            Specification: Horizontal 2K-injection moulding machine,
            DEMAG Multi 420/810-2300h/430
            incl. handling

            injection unit 1:
            - Screw diameter: 70 mm
            - injection volume: 1.112 cm³
            - weight: 880 g

            injection unit 2:
            - Screw diameter: 15 mm
            - injection volume: 292 cm³
            - weight: 190 g

            Clamping unit:
            - Clamping force: 1200 kN
            - Centring: 160 mm
            - Platen size: 1200 x 1100 mm
            - Mould size: 810 x 710 mm
            - Mould thickness min.: 380 mm
            - Mould thickness max.: 940 mm

            - 4 & 4 Cascades
            - 4x core pull
            - Handling: Yes

            - Voltage: 3x 400V, 50Hz, N, PE
            - Total power: 192 kW
            - Dimensions L/W/H: approx. 7,900 x 2,200 x 5,000 mm
            - Weight approx.: 25,000 kg

            Further DEMAG plastic injection moulding machines and a
            conveyor control/material station for 4 to 56
            separators for granulate conveying on our homepage.



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machines (plastic) DEMAG ergotech System 60/420-200


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-L230202 · Injection-moulding machines (plastic)

          DEMAG - ergotech System 60/420-200 - - 2007 -

          Technical details
          clamping force 600 kN︱injection volume 106 cm³︱screw diameter 30 mm︱platen size 590 x 600 mm︱
          Condition: used, Specification: Horizontal injection moulding machine, type: System 60/420-200 - Internat. Size specification: 600 - 200 injection unit: - Screw diameter: 30 mm - L/D - ratio: 20D - Injection volume: 106 cm³ - Injection pressure: 1995 bar - Cylinder heating: 8,3 kW clamping unit: - Clamping force: 600 kN - Max. opening stroke: 450 mm - Mould installation height: min. 250 mm - Max. platen distance: 700 mm - Mould clamping platens: 590 x 600 mm - Clear column distance: 420 x 420 mm Total machine: - Oil tank filling: 180 ltr. - Pump capacity: 22 kW - Voltage: 3x 400V, 50 Hz - total power: 30,3 kW - Dimensions L/W/H: approx. 4200 x 1400 x 2000 mm - Weight without oil approx.: 3,950 kg - 2x core pull Plant is still in production and will be available from approx. available.
            clamping force 600 kN
            injection volume 106 cm³
            screw diameter 30 mm
            platen size 590 x 600 mm
            Description :
            Condition: used,

            Specification: Horizontal injection moulding machine,
            type: System 60/420-200

            - Internat. Size specification: 600 - 200

            injection unit:
            - Screw diameter: 30 mm
            - L/D - ratio: 20D
            - Injection volume: 106 cm³
            - Injection pressure: 1995 bar
            - Cylinder heating: 8,3 kW

            clamping unit:
            - Clamping force: 600 kN
            - Max. opening stroke: 450 mm
            - Mould installation height: min. 250 mm
            - Max. platen distance: 700 mm
            - Mould clamping platens: 590 x 600 mm
            - Clear column distance: 420 x 420 mm

            Total machine:
            - Oil tank filling: 180 ltr.
            - Pump capacity: 22 kW
            - Voltage: 3x 400V, 50 Hz
            - total power: 30,3 kW
            - Dimensions L/W/H: approx. 4200 x 1400 x 2000 mm
            - Weight without oil approx.: 3,950 kg

            - 2x core pull

            Plant is still in production and will be available from approx.
            available.



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machines (plastic) ENGEL VC 80H/80L / 130 Combi


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-L200203 · Injection-moulding machines (plastic)

          ENGEL - VC 80H/80L / 130 Combi - - 2006 -

          Technical details
          clamping force 1.300 kN︱injection volume 106 / 43 cm³︱screw diameter 30 / 25 mm︱platen size 850 x 750 mm︱daylight between platens - max. 900 mm︱
            clamping force 1.300 kN
            injection volume 106 / 43 cm³
            screw diameter 30 / 25 mm
            platen size 850 x 750 mm
            daylight between platens - max. 900 mm
            Description :




        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machines (plastic) ENGEL ES 1350 H 500 W/400 HL-2 F


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-L200202 · Injection-moulding machines (plastic)

          ENGEL - ES 1350 H 500 W/400 HL-2 F - - 2005 -

          Technical details
          clamping force 4.000 kN︱injection volume 735 cm³︱screw diameter 60 mm︱platen size 1.400 x 1.030 mm︱
          Condition: used, Specification: horizontal injection moulding machine, factory no: Injection unit 1: - screw diameter: 60 mm - metering stroke: 200 mm - Screw speed: 226 rpm - Injection flow: 351 cm³/sec - Injection volume: 735 cm³ - Spec. injection pressure: 1.489 bar - Spec. injection pressure increased: 2,011 bar Injection unit 2: - Screw diameter: 40 mm - Metering stroke: 140 mm - Screw speed: 400 rpm - Injection flow: 197 cm³/sec - Injection volume: 251 cm³ - Spec. injection pressure: 1.286 bar - Spec. injection pressure increased: 2.029 bar Clamping unit: - Clamping force max.: 4,000 kN - Clamping platens: 1,400 x 1030 mm - Opening stroke: 954 mm - Max. platen distance: 1,520 mm - Ejector stroke: 250 mm - Ejector force: 83.0 kN - Connected load: 193 kW - Operating hours: 93421 hours - Hydraulic core pull: 2 FAP 4 BAP Handling: ERC 84/1-E RC 100 integrated
            clamping force 4.000 kN
            injection volume 735 cm³
            screw diameter 60 mm
            platen size 1.400 x 1.030 mm
            Description :
            Condition: used,

            Specification: horizontal injection moulding machine,
            factory no:

            Injection unit 1:
            - screw diameter: 60 mm
            - metering stroke: 200 mm
            - Screw speed: 226 rpm
            - Injection flow: 351 cm³/sec
            - Injection volume: 735 cm³
            - Spec. injection pressure: 1.489 bar
            - Spec. injection pressure increased: 2,011 bar

            Injection unit 2:
            - Screw diameter: 40 mm
            - Metering stroke: 140 mm
            - Screw speed: 400 rpm
            - Injection flow: 197 cm³/sec
            - Injection volume: 251 cm³
            - Spec. injection pressure: 1.286 bar
            - Spec. injection pressure increased: 2.029 bar

            Clamping unit:
            - Clamping force max.: 4,000 kN
            - Clamping platens: 1,400 x 1030 mm
            - Opening stroke: 954 mm
            - Max. platen distance: 1,520 mm
            - Ejector stroke: 250 mm
            - Ejector force: 83.0 kN

            - Connected load: 193 kW
            - Operating hours: 93421 hours
            - Hydraulic core pull:
            2 FAP
            4 BAP

            Handling: ERC 84/1-E RC 100 integrated



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machines (plastic) DEMAG ergotech-multi 80-420


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-L230503 · Injection-moulding machines (plastic)

          DEMAG - ergotech-multi 80-420 - - 2003 -

          Technical details
          clamping force 800 kN︱injection volume 106 / 42 cm³︱screw diameter 30 / 22 mm︱platen size 600 x 600 mm︱
          Condition: used, Specification: Horizontal 2K-injection moulding machine, injection unit 1: - Screw diameter: 30 mm - injection volume: 106 cm³ - weight: 94 g injection unit 2: - Screw diameter: 22 mm - injection volume: 42 cm³ - weight: 37 g Clamping unit: - Clamping force: 800 kN - Centring: 125 mm - Platen size: 600 x 600 mm - Mould size: 420 x 420 mm - Mould thickness min.: 250 mm - Mould thickness max.: 590 mm - Voltage: 3x 400V, 50Hz, N, PE - Total power: 42 kW - Dimensions L/W/H: approx. 4,300 x 1,400 x 3,600 mm - Weight approx.: 5,750 kg Further DEMAG plastic injection moulding machines and a conveyor control/material station for 4 to 56 separators for granulate conveying on our homepage.
            clamping force 800 kN
            injection volume 106 / 42 cm³
            screw diameter 30 / 22 mm
            platen size 600 x 600 mm
            Description :
            Condition: used,

            Specification: Horizontal 2K-injection moulding machine,

            injection unit 1:
            - Screw diameter: 30 mm
            - injection volume: 106 cm³
            - weight: 94 g

            injection unit 2:
            - Screw diameter: 22 mm
            - injection volume: 42 cm³
            - weight: 37 g

            Clamping unit:
            - Clamping force: 800 kN
            - Centring: 125 mm
            - Platen size: 600 x 600 mm
            - Mould size: 420 x 420 mm
            - Mould thickness min.: 250 mm
            - Mould thickness max.: 590 mm

            - Voltage: 3x 400V, 50Hz, N, PE
            - Total power: 42 kW
            - Dimensions L/W/H: approx. 4,300 x 1,400 x 3,600 mm
            - Weight approx.: 5,750 kg

            Further DEMAG plastic injection moulding machines and a
            conveyor control/material station for 4 to 56
            separators for granulate conveying on our homepage.



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machines (plastic) ARBURG Allrounder 470S-1300-350


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-L240301 · Injection-moulding machines (plastic)

          ARBURG - Allrounder 470S-1300-350 - - 2002 -

          Technical details
          clamping force 1300 kN︱injection volume -- cm³︱screw diameter 45 mm︱platen size 470 x 470 mm︱
          Condition: used, Specification: Horizontal injection moulding machine, Type: Allrounder 470 S 1300-350 Injection unit: - Screw diameter: 45 mm - Centring ring diameter: 125 mm - Shot weight max.: 210 g (PS) - Injection pressure: 1,840 bar Clamping unit: - Clamping force: 1300 kN - Opening stroke max.: 850 mm - Mould installation height: min. 275 mm - Mould mounting platens: 470 x 470 mm - Operating hours approx.: 91,000 - Core pulls: 1x - Valve gate: 1x pneumatic - Hot runner control points: 12x - Temperature control unit interfaces: 6x (20 mA) - Conveyor belt in the machine - Selector unit. available - Release for high temperature up to 450°C - Communication card for ProSeS interface available - Robot interface available. Technical precision parts were produced. Regularly maintained and calibrated. Without accessories such as peripheral devices, conveyors, robots, etc. and without material hopper.
            clamping force 1300 kN
            injection volume -- cm³
            screw diameter 45 mm
            platen size 470 x 470 mm
            Description :
            Condition: used,

            Specification: Horizontal injection moulding machine,
            Type: Allrounder 470 S 1300-350

            Injection unit:
            - Screw diameter: 45 mm
            - Centring ring diameter: 125 mm
            - Shot weight max.: 210 g (PS)
            - Injection pressure: 1,840 bar

            Clamping unit:
            - Clamping force: 1300 kN
            - Opening stroke max.: 850 mm
            - Mould installation height: min. 275 mm
            - Mould mounting platens: 470 x 470 mm
            - Operating hours approx.: 91,000

            - Core pulls: 1x
            - Valve gate: 1x pneumatic
            - Hot runner control points: 12x
            - Temperature control unit interfaces: 6x (20 mA)
            - Conveyor belt in the machine
            - Selector unit. available
            - Release for high temperature up to 450°C
            - Communication card for ProSeS interface available
            - Robot interface available.

            Technical precision parts were produced.
            Regularly maintained and calibrated.

            Without accessories such as peripheral devices,
            conveyors, robots, etc. and without material hopper.



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machines (plastic) DEMAG ergotech pro 100-400 viva


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-L230504 · Injection-moulding machines (plastic)

          DEMAG - ergotech pro 100-400 viva - - 2001 -

          Technical details
          clamping force 1.000 kN︱injection volume 203 cm³︱screw diameter 40 mm︱platen size 580 x 652 mm︱
          Condition: used, Specification: Horizontal 2K-injection moulding machine, injection unit 1: - Screw diameter: 40 mm - injection volume: 230 cm³ - weight: 205 g Clamping unit: - Clamping force: 1000 kN - Centring: 125 mm - Platen size: 580 x 652 mm - Mould size: 400 x 400 mm - Mould thickness min.: 250 mm - Mould thickness max.: 450 mm - 1x core pull - Voltage: 3x 400V, 50Hz, N, PE - Total power: 25 kW - Dimensions L/W/H: approx. 4,350 x 1,400 x 1,900 mm - Weight approx.: 4,750 kg Further DEMAG plastic injection moulding machines and a conveyor control/material station for 4 to 56 separators for granulate conveying on our homepage.
            clamping force 1.000 kN
            injection volume 203 cm³
            screw diameter 40 mm
            platen size 580 x 652 mm
            Description :
            Condition: used,

            Specification: Horizontal 2K-injection moulding machine,

            injection unit 1:
            - Screw diameter: 40 mm
            - injection volume: 230 cm³
            - weight: 205 g

            Clamping unit:
            - Clamping force: 1000 kN
            - Centring: 125 mm
            - Platen size: 580 x 652 mm
            - Mould size: 400 x 400 mm
            - Mould thickness min.: 250 mm
            - Mould thickness max.: 450 mm

            - 1x core pull

            - Voltage: 3x 400V, 50Hz, N, PE
            - Total power: 25 kW
            - Dimensions L/W/H: approx. 4,350 x 1,400 x 1,900 mm
            - Weight approx.: 4,750 kg

            Further DEMAG plastic injection moulding machines and a
            conveyor control/material station for 4 to 56
            separators for granulate conveying on our homepage.



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machines (plastic) DEMAG ergotech viva 80-400


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-L230201 · Injection-moulding machines (plastic)

          DEMAG - ergotech viva 80-400 - - 2001 -

          Technical details
          clamping force 800 kN︱injection volume 177 cm³︱screw diameter 35 mm︱platen size 580 x 580 mm︱
          Condition: used, Specification: Horizontal injection moulding machine, type: Ergotech viva 80-400 - Internat. Size specification: 800 - 400 injection unit: - Screw diameter: 35 mm - L/D - ratio: 20D - Injection volume: 177 cm³ - Injection pressure: 2387 bar - Cylinder heating: 8,8 kW clamping unit: - Clamping force: 800 kN - Max. opening stroke: 450 mm - Mould installation height: min. 250 mm - Max. platen distance: 700 mm - Mould clamping platens: 580 x 580 mm - Clear column distance: 400 x 400 mm Total machine: - Oil tank filling: 220 ltr. - Pump capacity: 15 kW - Voltage: 3x 400V, 50 Hz, N, PE - total power: 23,8 kW - Dimensions L/W/H: approx. 4250 x 1270 x 1795 mm - Weight without oil approx.: 3,600 kg - 1x core pull Plant is still in production and will be available from approx. available.
            clamping force 800 kN
            injection volume 177 cm³
            screw diameter 35 mm
            platen size 580 x 580 mm
            Description :
            Condition: used,

            Specification: Horizontal injection moulding machine,
            type: Ergotech viva 80-400

            - Internat. Size specification: 800 - 400

            injection unit:
            - Screw diameter: 35 mm
            - L/D - ratio: 20D
            - Injection volume: 177 cm³
            - Injection pressure: 2387 bar
            - Cylinder heating: 8,8 kW

            clamping unit:
            - Clamping force: 800 kN
            - Max. opening stroke: 450 mm
            - Mould installation height: min. 250 mm
            - Max. platen distance: 700 mm
            - Mould clamping platens: 580 x 580 mm
            - Clear column distance: 400 x 400 mm

            Total machine:
            - Oil tank filling: 220 ltr.
            - Pump capacity: 15 kW
            - Voltage: 3x 400V, 50 Hz, N, PE
            - total power: 23,8 kW
            - Dimensions L/W/H: approx. 4250 x 1270 x 1795 mm
            - Weight without oil approx.: 3,600 kg

            - 1x core pull

            Plant is still in production and will be available from approx.
            available.



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machines (plastic) DEMAG ergotech 150/475-440


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-L201202 · Injection-moulding machines (plastic)

          DEMAG - ergotech 150/475-440 - - 1999 -

          Technical details
          clamping force -- kN︱injection volume 230 cm³︱screw diameter 40 mm︱platen size 475 x 475 mm︱
          Condition: used, Specification: Horizontal injection moulding machine, injection unit: - Screw diameter: 40 mm - Cylinder diameter: 40 mm - Spraying volume: 230 cm³. Clamping unit: - tie bar distance: 475 x 475 mm - Operating hours approx.: 30000 h - Air valve - Core pull - 12-way hot runner controller
            clamping force -- kN
            injection volume 230 cm³
            screw diameter 40 mm
            platen size 475 x 475 mm
            Description :
            Condition: used,

            Specification: Horizontal
            injection moulding machine,

            injection unit:
            - Screw diameter: 40 mm
            - Cylinder diameter: 40 mm
            - Spraying volume: 230 cm³.

            Clamping unit:
            - tie bar distance: 475 x 475 mm
            - Operating hours approx.: 30000 h

            - Air valve
            - Core pull
            - 12-way hot runner controller




        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          used Injection Moulding Injection-moulding machines (plastic) DEMAG ergotech 650-5200-610


          • MEB Maschinenhandel GmbH
          • Schwalbenweg 4
          • 30826 Garbsen
          • Deutschland

          • (0)5031 9394-634
          • info@meb-maschinenhandel.de
            www.meb-maschinenhandel.de
          #2037-L230507 · Injection-moulding machines (plastic)

          DEMAG - ergotech 650-5200-610 - - 1999 -

          Technical details
          clamping force 6500 kN︱injection volume 2011 / 323 cm³︱screw diameter 80 / 45 mm︱platen size 1450 x 1350 mm︱
          Condition: used, Specification: Horizontal 2K-injection moulding machine, DEMAG ergotech 650-5200-610 incl. handling injection unit 1: - Screw diameter: 80 mm - injection volume: 2.011 cm³ - weight: 1810 g injection unit 2: - Screw diameter: 45 mm - injection volume: 323 cm³ - weight: 290 g Clamping unit: - Clamping force: 6500 kN - Centring: 200 mm - Platen size: 1450 x 1350 mm - Mould size: 1000 x 910 mm - Mould thickness min.: 450 mm - Mould thickness max.: 950 mm - 2x core pull - Handling: Yes - Voltage: 3x 400V, 50Hz, N, PE - Total power: 245 kW - Dimensions L/W/H: approx. 10,100 x 5,500 x 5,000 mm - Weight approx.: 36,000 kg Further DEMAG plastic injection moulding machines and a conveyor control/material station for 4 to 56 separators for granulate conveying on our homepage.
            clamping force 6500 kN
            injection volume 2011 / 323 cm³
            screw diameter 80 / 45 mm
            platen size 1450 x 1350 mm
            Description :
            Condition: used,

            Specification: Horizontal 2K-injection moulding machine,
            DEMAG ergotech 650-5200-610
            incl. handling

            injection unit 1:
            - Screw diameter: 80 mm
            - injection volume: 2.011 cm³
            - weight: 1810 g

            injection unit 2:
            - Screw diameter: 45 mm
            - injection volume: 323 cm³
            - weight: 290 g

            Clamping unit:
            - Clamping force: 6500 kN
            - Centring: 200 mm
            - Platen size: 1450 x 1350 mm
            - Mould size: 1000 x 910 mm
            - Mould thickness min.: 450 mm
            - Mould thickness max.: 950 mm

            - 2x core pull
            - Handling: Yes

            - Voltage: 3x 400V, 50Hz, N, PE
            - Total power: 245 kW
            - Dimensions L/W/H: approx. 10,100 x 5,500 x 5,000 mm
            - Weight approx.: 36,000 kg

            Further DEMAG plastic injection moulding machines and a
            conveyor control/material station for 4 to 56
            separators for granulate conveying on our homepage.



        • MEB Maschinenhandel GmbH
        • Schwalbenweg 4
        • 30826 Garbsen
        • Deutschland

        • Datasheet
          Request / Contact
          •   
          •   
          • 1  
          • 2  
          •   
          •